ÿWPCL ûÿ2BJ|xÐ ` ÐÐÌÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿH øÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÌÐÐ °°°è ÐÑ Âx„|ü@Ž ÑÐ Å@8Ø'@8Ø'Å Ð 14.ÁHÁÓÓÃÃRecommendation G.755ÄÄ Áà%ÁDIGITAL MULTIPLEX EQUIPMENT OPERATING AT 139 264 KBIT/S ƒ Áà(ÁAND MULTIPLEXING THREE TRIBUTARIES AT 44736 KBIT/Sƒ 1.ÁHÁÃÃGeneralÄÄ Ð 8 ÐÁHÁThe digital multiplex equipment described in this Recommendation is intended for use between networks using different digital hierarchies as specified in Recommendations G.702 and G.802. 2.ÁHÁÃÃBit rateÄÄ ÁHÁThe bit rates of the tributary and multiplex signals should be 44736 kbit/s ©ÃÃ+ÄÄ20 ppm and 139 264 kbit/s ©ÃÃ+ÄÄ15 ppm, respectively, as specified in Recommendation G.703. 3.ÁHÁÃÃFrame structureÄÄ ÁHÁTable 1/G.755 gives the recommended 139 264 kbit/s multiplexing frame structure. 4.ÁHÁÃÃLoss and recovery of frame alignment and consequent actionÄÄ Ð X ÐÁHÁLoss of frame alignment should be assumed to have taken place when four consecutive frame alignment signals have been incorrectly received in their predicted positions. ÁHÁWhen frame alignment is assumed to be lost, the frame alignment device should decide that such alignment has effectively been recovered when it detects the presence of three consecutive correct frame alignment signals. ÁHÁThe frame alignment device having detected the appearance of a single correct frame alignment signal, should begin a new search for the frame alignment signal when it detects the absence of the frame alignment signal in one of the two following frames. ÃÃNoteÄÄ © As it is not strictly necessary to specify the detailed frame alignment strategy, any suitable frame alignment strategy may be used provided the performance achieved is at least as efficient in all respects as that obtained by the above frame alignment strategy. 5.ÁHÁÃÃMultiplexing and justification methodsÄÄ ÁHÁCyclic bit interleaving in the tributary numbering order and positive justification are recommended. ÁHÁThe justification control signal should be distributed and use the CÃÃjiÄÄ©bits (J=1,2,3; i=1,2,3,4,5) (see Note 6 to Table 1/G.75x). ÁHÁPositive justification should be indicated by the justification control signal 11111 and no justification by the signal 00000. Majority decision is recommended. ÁHÁTable 1/G.755 gives the maximum justification rate per tributary and the nominal justification ratio. ÁàÀJÁTABLE 1/G.755ƒ ÁàÀ;ÁÃÃ139 264 kbit/s multiplexing frame structureÄă  À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À  À À     Nominal tributary bit rate (kbit/s)                        À À44736 À À  À À     Number of tributaries                                      À À3 À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À À À À À À  À À                      Frame structure                           À ÀBit number À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À À À À À À  À À                                                                À ÀÃÃSet IÄÄ À À  À À     Frame alignment signal (111110100000)                      À À1 to 12 À À  À À     Bits from tributaries                                      À À13 to 159 À À  À À                                                                À ÀÃÃSet IIÄÄ À À  À À     Justification control bits CÃÃj1ÄÄ (Note 6)                    À À1 to 3 À À  À À     Bits from tributaries                                      À À4 to 159 À À  À À                                                                À ÀÃÃSet IIIÄÄ À À  À À     Justification control bits CÃÃj2ÄÄ (Note 6)                    À À1 to 3 À À  À À     Bits from tributaries                                      À À4 to 159 À À  À À                                                                À ÀÃÃSet IVÄÄ À À  À À     Justification control bits CÃÃj3ÄÄ (Note 6)                    À À1 to 3 À À  À À     Alarm indication to the remote multiplex equipment (Note 1)À À4 À À  À À     Parity bit (Notes 2, 3 and 4)                              À À5 À À  À À     Bits reserved for future use (Note 5)                      À À6 to 9 À À  À À     Bits from tributaries                                      À À10 to 159 À À  À À                                                                À ÀÃÃSet VÄÄ À À  À À     Justification control bits CÃÃj4ÄÄ (Note 6)                    À À1 to 3 À À  À À     Bits from tributaries                                      À À4 to 159 À À  À À                                                                À ÀÃÃSet VIÄÄ À À  À À     Justification control bits CÃÃj5ÄÄ (Note 6)                    À À1 to 3 À À  À À     Bits from tributaries available for justification          À À4 to 6 À À  À À     Bits from tributaries                                      À À7 to 159 À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ  À À     Frame length (bits)                                        À À954 À À  À À     Bits per tributary in a frame (bits)                       À À307 À À  À À     Maximum justification rate per tributary (kbit/s)          À À146.0 À À  À À     Nominal justification ratio                                À À0.545 À À  À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À ÃÃNote 1ÄÄ © See section 10.2.1. ÃÃNote 2ÄÄ © The parity bit = 1 if the number of marks in all tributary bits including the bits in the justifiable time©slots in the preceding frame is odd; the parity bit = 0 if the number of marks in all tributary bits including the bits in the justifiable time©slots in the preceding frame is even. ÃÃNote 3ÄÄ © It is recognized that existing multiplex equipment installed prior to adoption of this Recommendation do not insert the parity bit. ÃÃNote 4ÄÄ © The implementation and the use of this parity bit procedure are for further study. ÃÃNote 5ÄÄ © These bits should be set to 1 when not used. ÃÃNote 6ÄÄ © CÃÃjiÄÄ (j=1,2,3; i=1,2,3,4,5) indicates the ith justification control bit of the jth tributary. 6.ÁHÁÃÃJitterÄÄ 6.1ÁHÁÃÃDemultiplexer tributary jitter transfer characteristicÄÄ ÁHÁThe demultiplexer 44736 kbit/s tributary jitter transfer characteristic should meet the gain/frequency limits given in Figure 1/G.75x. The equivalent binary content of the test signal used should result in a tributary output signal of 1000.Ô w.ÔŒ ÃÃNote 1ÄÄ © This characteristic is usually measured between the high speed and low speed interfaces of the demultiplexer and the measurements are taken in unit intervals. It is then necessary to introduce a correction factor to account for the difference in the size of unit intervals. ÃÃNote 2ÄÄ © In addition, the need to specify a muldex jitter transfer characteristic is for further study. ÃÃNote 3ÄÄ © It is recognized that the existing multiplex equipment designed prior to the adoption of this Recommendation might need tributary test signals incorporating the 44736 kbit/s frame structure defined in G.752. ÃÃNoteÄÄ © The frequency fÃÃOÄÄ should be as low as possible, taking into account the limitations of measuring equipment. In any case fÃÃOÄÄ should be no greater than 10 Hz. ÁHÁThe selective measurement method should be used. ÁàÀIÁFIGURE 1/G.755ƒ ÁàÀPÁƒ ÁàÀ5ÁÃÃDemultiplexer tributary jitter transfer characteristicÄă 6.2ÁHÁÃÃOutput jitterÄÄ 6.2.1ÁHÁÃÃTributary output jitterÄÄ ÁHÁWith no jitter applied to the input ports of the multiplexer and with the multiplexer directly connected to the demultiplexer, the peak©to©peak jitter at the tributary output port should not exceed 0.3 UI when measured over a one minute interval within the frequency range from fÃÃ1ÄÄ = 10 Hz to fÃÃ4ÄÄ = 400 kHz. ÁHÁWhen measured with an instrument incorporating a bandpass filter having a lower cutoff frequency of fÃÃ3ÄÄ = 60 kHz, a roll©off of 20 dB/decade and an upper limit of fÃÃ4ÄÄ = 400 kHz, the peak©to©peak output jitter should not exceed 0.05 UI when it is measured over a one minute interval. 6.2.2ÁHÁÃÃMultiplexer output jitterÄÄ ÁHÁThe peak©to©peak jitter at the 139 264 kbit/s output port should not exceed 0.05 UI when it is measured over a one minute interval within the frequency range from 200 Hz to 3 500 kHz. 6.3ÁHÁÃÃInput jitterÄÄ 6.3.1ÁHÁÃÃTributary input jitterÄÄ ÁHÁThe 44736 kbit/s input port should be capable of accommodating levels of input jitter up to the limits given in Figure 2/G.755. ÃÃNoteÄÄ © Current Recommendation G.703 does not refer to the jitter to be tolerated at the digital distribution frame at 44736 kbit/s nor at the input port of equipment connected to this distribution frame.          À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À          À À À À À À          À ÀPeak©to©peak sinusoidal  À À             Frequency                À À          À À   jitter amplitude      À À                                      À À          ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ          À À            À À            À À         À À         À À         À À        À À          À À   AÃÃ1ÄÄ [UI]  À À  AÃÃ2ÄÄ [UI]   À À fÃÃ1ÄÄ [Hz] À À fÃÃ2ÄÄ [Hz] À À fÃÃ3ÄÄ [Hz] À À fÃÃ4ÄÄ [Hz]À À          ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ          À À            À À            À À         À À         À À         À À        À À          À À     5.0    À À    0.1     À À   10    À À  2.3 k  À À   60 k  À À  400 k À À          À À            À À            À À         À À         À À         À À        À À          À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À ÁàÀIÁFIGURE 2/G.755ƒ ÁàÀPÁƒ ÁàÀ4ÁÃÃLower limit of maximum tolerable sinusoidal input jitterÄă ÁàÀIÁÃÃat 44736 kbit/sÄă ÁàÀPÁƒ 6.3.2ÁHÁÃÃDemultiplexer input jitterÄÄ ÁHÁThe 139 264 kbit/s input port should be capable of accommodating levels of input jitter up to the limits given in Recommendation G.823. ÃÃNoteÄÄ © The jitter accommodation requirement should be met when the jittered input signal is composed of the multiplexed tributary signals having any value of jitter allowed for the 44736 kbit/s level. 7.ÁHÁÃÃDigital interfacesÄÄ ÁHÁThe digital interfaces at 44736 kbit/s and 139 264 kbit/s should be in accordance with Recommendation G.703. 8.ÁHÁÃÃTiming signalÄÄ ÁHÁIf it is economically feasible, it may be desirable to be able to derive the multiplexing timing signal from an external source as well as from an internal source. Ô w.ÔŒ9.ÁHÁÃÃService digitsÄÄ ÁHÁSix bits per frame are available for service functions (see Table 1/G.755): bit 4 of Set IV is used to transmit an alarm indication to the remote multiplex equipment when specific fault conditions are detected in the multiplex equipment (see section 10 below); bit 5 of Set IV may be used for parity check; bits 6 to 9 of Set IV are reserved for future use. 10.ÁHÁÃÃFault conditions and consequent actionsÄÄ 10.1ÁHÁÃÃFault conditionsÄÄ 10.1.1Á  ÁThe digital multiplex equipment should detect the following fault conditions: ÁHÁ1)Á   Áfailure of power supply; Ð ø ÐÂHHÂ2)Âh   Âloss of an incoming 44736 kbit/s tributary signal at a multiplexer input port;ÆÆ Ð ` Ð Ð  ÐÁHÁ3)Âh   Âloss of an incoming 139 264 kbit/s multiplex signal at a demultiplexer input port;ÆÆ Ð H ÐÂHHÂÃÃNoteÄÄ © The detection of this fault condition is required only when it does not result in an indication of loss of frame alignment.ÆÆ Ð ` Ð Ð ( ÐÁHÁ4)Âh   Âloss of frame alignment signal at a demultiplexer input port;ÆÆ ÁHÁ5)Âh   Âdetection of an alarm indication received from the remote multiplex equipment at a demultiplexer input port;ÆÆ ÁHÁ6)Âh   Âdetection of alarm indication signal (AIS) at a demultiplexer input port.ÆÆ Ð à ÐÃÃNote 1ÄÄ © The equivalent binary content of the AIS at 139 264 kbit/s should be a continuous stream of binary ones (marks) as recommended in Recommendation M.20. ÃÃNote 2ÄÄ © The strategy for detecting the presence of the AIS should be such that the AIS is detectable even in the presence of an error ratio of 1.10Ãé3ÄÄ. However, a signal with all bits except the frame alignment signal in the state of 1, should not be mistaken as an AIS. 10.1.2Á  ÁThe need to monitor the degradation of the incoming 139 264 kbit/s signal for the purpose of end©to©end error performance monitoring of the 139 264 kbit/s digital block as well as the procedure for detecting such degradation are for further study. 10.2ÁHÁÃÃConsequent actionsÄÄ ÁHÁFurther to the detection of a fault condition, the appropriate actions should be taken as specified in Table 2/G.755. ÃÃNote 1ÄÄ © The concept and definition of prompt maintenance alarm indication is given in Recommendation M.20. ÃÃNote 2ÄÄ © When the alarm indication signal (AIS) is detected at the input of the demultiplexer, the prompt maintenance alarm indication associated with loss of frame alignment should be inhibited, while the rest of the consequent actions are in accordance with those associated in Table 2/G.755 with the fault condition. Ð x Ð10.2.1Á  ÁAlarm indication to the remote multiplex equipment should be generated by changing bit 4 of Set IV (see Table 1/G.755) from the state 0 to the state 1. 10.2.2Á  ÁAIS should be applied to the following as specified in Table 2/G.755: ÁHÁ©Âà  Âall three 44736 kbit/s tributary outputs from the demultiplexer;ÆÆ ÁHÁ©Âà  Â139 264 kbit/s output of the multiplexer;ÆÆ ÁHÁ©Âà  Âthe time slots of the 139 264 kbit/s signal at the output of the multiplexer, corresponding to the relevant 44736 kbit/s tributary.ÆÆ ÃÃNoteÄÄ © The equivalent binary content of the AIS at 44736 kbit/s is a signal with a valid frame alignment signal, parity and justification control bits as defined in Table 2/G.752, with the tributary bits being set to a 1010... sequence, starting with a binary 1 after each frame alignment, multi©frame alignment and justification control bit, and with all justification control bits being set to binary 0. Áà°NÁTABLE 2/G.755ƒ Áà°TÁƒ Áà°AÁÃÃFault conditions and consequent actionsÄă Áà°TÁƒ À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À À À À À À À Consequent actions (see ÀÀ 10.2) À À À À À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À À À À À À À À À À AIS applied À À À À À À À À À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À ÀEquipmentÀ ÀFault À ÀPrompt À ÀAlarm À À À À À ÀTo the À À À Àpart À Àcondition À ÀmaintenanceÀ ÀindicationÀ À À À À Àrelevant À À À À À À(see ÀÀ 10.1)À Àalarm À Àto the À ÀTo all the À ÀTo the À Àtime À À À À À À À Àindication À Àremote À ÀtributariesÀ ÀcompositeÀ Àslots of À À À À À À À Àgenerated À Àmultiplex À À À Àsignal À Àthe À À À À À À À À À Àequipment À À À À À ÀcompositeÀ À À À À À À À À Àgenerated À À À À À Àsignal À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À ÀMulti© À ÀFailure of À À Yes À À À ÀYes, if À ÀYes, if À À À À À Àplexer À Àpower À À À À À ÀpracticableÀ Àpracti© À À À À À Àand À Àsupply À À À À À À À Àcable À À À À À Àdemulti© À À À À À À À À À À À À À À À Àplexer À À À À À À À À À À À À À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À ÀMulti© À ÀLoss of in© À À Yes À À À À À À À À Yes À À À Àplexer À Àcoming À À À À À À À À À À À À À Àonly À Àsignal on a À À À À À À À À À À À À À À À Àtributary À À À À À À À À À À À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À À À ÀLoss of in© À À Yes À À Yes À À Yes À À À À À À À À À Àcoming À À À À À À À À À À À À À À À Àsignal À À À À À À À À À À À À À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À ÀDemulti© À ÀLoss of À À Yes À À Yes À À Yes À À À À À À À Àplexer À Àframe À À À À À À À À À À À À À Àonly À Àalignment À À À À À À À À À À À À À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À À À ÀAlarm À À À À À À À À À À À À À À À Àindication À À À À À À À À À À À À À À À Àreceived À À À À À À À À À À À À À À À Àfrom the À À À À À À À À À À À À À À À Àremote À À À À À À À À À À À À À À À Àmultiplex À À À À À À À À À À À À À À À Àequipment À À À À À À À À À À À À À ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ À Ô w.ÔŒÃÃNoteÄÄ © A Yes in the table signifies that a certain action should be taken as a consequence of the relevant fault condition. An open space in the table signifies that the relevant action should not be taken as a consequence of the relevant fault condition, if this condition is the only one present. If more than one fault condition is simultaneously present, the relevant action should be taken if, for at least one of the conditions, a Yes is defined in relation to this action. Áà°PÁÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀƒ Áà°TÁƒ