be able to identify various WAN standards. Web Links WAN http://www.cisco.com/en/US/tech/tk713/ tech_topology_and_network_ serv_and_protocol_suite_ home.html
Content 2.1 WAN Technologies Overview 2.1.4 WAN encapsulation Data from the network layer is passed to the data link layer for delivery on a physical link, which is normally point-to-point on a WAN connection. The data link layer builds a frame around the network layer data so the necessary checks and controls can be applied. Each WAN connection type uses a Layer 2 protocol to encapsulate traffic while it is crossing the WAN link. To ensure that the correct encapsulation protocol is used, the Layer 2 encapsulation type used for each router serial interface must be configured. The choice of encapsulation protocols depends on the WAN technology and the equipment. Most framing is based on the HDLC standard.HDLC framing gives reliable delivery of data over unreliable lines and includes signal mechanisms for flow and error control. The frame always starts and ends with an 8-bit flag field, the bit pattern 01111110. Because there is a likelihood that this pattern will occur in the actual data, the sending HDLC system always inserts a 0 bit after every five 1s in the data field, so in practice the flag sequence can only occur at the frame ends. The receiving system strips out the inserted bits. When frames are transmitted consecutively the end flag of the first frame is used as the start flag of the next frame. The address field is not needed for WAN links, which are almost always point-to-point. The address field is still present and may be one or two bytes long. The control field indicates the frame type, which may be information, supervisory, or unnumbered: The control field is normally one byte, but will be two bytes for extended sliding windows systems. Together the address and control fields are called the frame header. The encapsulated data follows the control field. Then a frame check sequence (FCS) uses the cyclic redundancy check (CRC) mechanism to establish a two or four byte field. Several data link protocols are used, including sub-sets and proprietary versions of HDLC. Both PPP and the Cisco version of HDLC have an extra field in the header to identify the network layer protocol of the encapsulated data. Web Links WAN http://www.cisco.com/en/US/tech/tk713/ tech_topology_and_ network_serv_and_ protocol_suite_ home.html
Content 2.1 WAN Technologies Overview 2.1.5 Packet and circuit switching Packet-switched networks were developed to overcome the expense of public circuit-switched networks and to provide a more cost-effective WAN technology.When a subscriber makes a telephone call, the dialed number is used to set switches in the exchanges along the route of the call so that there is a continuous circuit from the originating caller to that of the called party. Because of the switching operation used to establish the circuit, the telephone system is called a circuit-switched network. If the telephones are replaced with modems, then the switched circuit is able to carry computer data. The internal path taken by the circuit between exchanges is shared by a number of conversations. Time division multiplexing (TDM) is used to give each conversation a share of the connection in turn. TDM assures that a fixed capacity connection is made available to the subscriber. If the circuit carries computer data, the usage of this fixed capacity may not be efficient. For example, if the circuit is used to access the Internet, there will be a burst of activity on the circuit while a web page is transferred. This could be followed by no activity while the user reads the page and then another burst of activity while the next page is transferred. This variation in usage between none and maximum is typical of computer network traffic. Because the subscriber has sole use of the fixed capacity allocation, switched circuits are generally an expensive way of moving data. An alternative is to allocate the capacity to the traffic only when it is needed, and share the available capacity between many users. With a circuit-switched connection, the data bits put on the circuit are automatically delivered to the far end because the circuit is already established. If the circuit is to be shared, there must be some mechanism to label the bits so that the system knows where to deliver them. It is difficult to label individual bits, therefore they are gathered into groups called cells, frames, or packets. The packet passes from exchange to exchange for delivery through the provider network. Networks that implement this system are called packet-switched networks. The links that connect the switches in the provider network belong to an individual subscriber during data transfer, therefore many subscribers can share the link. Costs can be significantly lower than a dedicated circuit-switched connection. Data on packet-switched networks are subject to unpredictable delays when individual packets wait for other subscriber packets to be transmitted by a switch. The switches in a packet-switched network determine, from addressing information in each packet, which link the packet must be sent on next. There are two approaches to this link determination, connectionless or connection-oriented. Connectionless systems, such as the Internet, carry full addressing information in each packet. Each switch must evaluate the address to determine where to send the packet. Connection-oriented systems predetermine the route for a packet, and each packet need only carry an identifier. In the case of Frame Relay, these are called Data Link Control Identifiers (DLCI). The switch determines the onward route by looking up the identifier in tables held in memory. The set of entries in the tables identifies a particular route or circuit through the system. If this circuit is only physically in existence while a packet is traveling through it, it is called a Virtual Circuit (VC). The table entries that constitute a VC can be established by sending a connection request through the network. In this case the resulting circuit is called a Switched Virtual Circuit (SVC). Data that is to travel on SVCs must wait until the table entries have been set up. Once established, the SVC may be in operation for hours, days or weeks. Where a circuit is required to be always available, a Permanent Virtual Circuit (PVC) will be established. Table entries are loaded by the switches at boot time so the PVC is always available. Web Links Packet vs Circuit Switching http://www.cina.org/ac051599/sld011.htm
Content 2.1 WAN Technologies Overview 2.1.6 WAN link options Figure provides an overview of WAN link options. Circuit switching establishes a dedicated physical connection for voice or data between a sender and receiver. Before communication can start, it is necessary to establish the connection by setting the switches. This is done by the telephone system, using the dialed number. ISDN is used on digital lines as well as on voice-grade lines. If the local loop is not directly connected to the telephone system, a digital subscriber line (DSL) may be available. To avoid the delays associated with setting up a connection, telephone