protocol that uses only optic fiber as a transmission medium. The maximum transmission distances depend on the type of fiber being used. When using single-mode fiber as the transmission medium, the maximum transmission distance is 40 kilometers (25 miles). Some discussions between IEEE members have begun that suggest the possibility of standards for 40, 80, and even 100-Gbps Ethernet. Web Links 10-Gigabit Ethernet http://www.cisco.com/en/US/tech/tk389/ tk214/tk771/ tech_protocol_home.html
Content 7.2 Gigabit and 10-Gigabit Ethernet 7.2.6 10-Gigabit Ethernet architectures As with the development of Gigabit Ethernet, the increase in speed comes with extra requirements. The shorter bit time duration because of increased speed requires special considerations. For 10 GbE transmissions, each data bit duration is 0.1 nanosecond. This means there would be 1,000 GbE data bits in the same bit time as one data bit in a 10-Mbps Ethernet data stream. Because of the short duration of the 10 GbE data bit, it is often difficult to separate a data bit from noise. 10 GbE data transmissions rely on exact bit timing to separate the data from the effects of noise on the physical layer. This is the purpose of synchronization. In response to these issues of synchronization, bandwidth, and Signal-to-Noise Ratio, 10-Gigabit Ethernet uses two separate encoding steps. By using codes to represent the user data, transmission is made more efficient. The encoded data provides synchronization, efficient usage of bandwidth, and improved Signal-to-Noise Ratio characteristics. Complex serial bit streams are used for all versions of 10GbE except for 10GBASE-LX4, which uses Wide Wavelength Division Multiplex (WWDM) to multiplex four bit simultaneous bit streams as four wavelengths of light launched into the fiber at one time. Figure represents the particular case of using four slightly different wavelength, laser sources. Upon receipt from the medium, the optical signal stream is demultiplexed into four separate optical signal streams. The four optical signal streams are then converted back into four electronic bit streams as they travel in approximately the reverse process back up through the sublayers to the MAC layer. Currently, most 10GbE products are in the form of modules, or line cards, for addition to high-end switches and routers. As the 10GbE technologies evolve, an increasing diversity of signaling components can be expected. As optical technologies evolve, improved transmitters and receivers will be incorporated into these products, taking further advantage of modularity. All 10GbE varieties use optical fiber media. Fiber types include 10µ single-mode Fiber, and 50µ and 62.5µ multimode fibers. A range of fiber attenuation and dispersion characteristics is supported, but they limit operating distances. Even though support is limited to fiber optic media, some of the maximum cable lengths are surprisingly short. No repeater is defined for 10-Gigabit Ethernet since half duplex is explicitly not supported. As with 10 Mbps, 100 Mbps and 1000 Mbps versions, it is possible to modify some of the architecture rules slightly. Possible architecture adjustments are related to signal loss and distortion along the medium. Due to dispersion of the signal and other issues the light pulse becomes undecipherable beyond certain distances. Web Links Next-Generation 50 µm Fiber Enhances 10-Gigabit Ethernet Performance http://www.corning.com/opticalfiber/ products__services/ Frame_products.asp? BodyURL= /opticalfiber/pdf/ wp4237%2Epdf
Content 7.2 Gigabit and 10-Gigabit Ethernet 7.2.7 Future of Ethernet Ethernet has gone through an evolution from Legacy → Fast → Gigabit → MultiGigabit technologies. While other LAN technologies are still in place (legacy installations), Ethernet dominates new LAN installations. So much so that some have referred to Ethernet as the LAN “dial tone”. Ethernet is now the standard for horizontal, vertical, and inter-building connections. Recently developing versions of Ethernet are blurring the distinction between LANs, MANs, and WANs. While 1-Gigabit Ethernet is now widely available and 10-Gigabit products becoming more available, the IEEE and the 10-Gigabit Ethernet Alliance are working on 40, 100, or even 160 Gbps standards. The technologies that are adopted will depend on a number of factors, including the rate of maturation of the technologies and standards, the rate of adoption in the market, and cost. Proposals for Ethernet arbitration schemes other than CSMA/CD have been made. The problem of collisions with physical bus topologies of 10BASE5 and 10BASE2 and 10BASE-T and 100BASE-TX hubs is no longer common. Using UTP and optical fiber with separate Tx and Rx paths, and the decreasing costs of switches make single shared media, half-duplex media connections much less important. The future of networking media is three-fold:
  1. Copper (up to 1000 Mbps, perhaps more)
  2. Wireless (approaching 100 Mbps, perhaps more)
  3. Optical fiber (currently at 10,000 Mbps and soon to be more)
Copper and wireless media have certain physical and practical limitations on the highest frequency signals that can be transmitted. This is not a limiting factor for optical fiber in the foreseeable future. The bandwidth limitations on optical fiber are extremely large and are not yet being threatened. In fiber systems, it is the electronics technology (such as emitters and detectors) and fiber manufacturing processes that most limit the speed. Upcoming developments in Ethernet are likely to be heavily weighted towards Laser light sources and single-mode optical fiber. When Ethernet was slower, half-duplex, subject to collisions and a “democratic” process for prioritization, was not considered to have the Quality of Service (QoS) capabilities required to handle certain types of traffic. This included such things as IP telephony and video multicast. The full-duplex high-speed Ethernet technologies that now dominate the market are proving to be sufficient at supporting even QoS-intensive applications. This makes the potential applications of Ethernet even wider. Ironically end-to-end QoS capability helped drive a push for ATM to the desktop and to the WAN in the mid-1990s, but now it is Ethernet, not ATM that is approaching this goal. Web Links Strategic Directions: Introduction to 10 Gigabit Ethernet http://www.cisco.com/en/US/tech/tk389/tk214/ technologies_white_ paper09186a0080092958.shtml
Content Summary An understanding of the following key points should have been achieved: