ATM-TRACE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, NOTIFICATION-TYPE, enterprises FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, TimeStamp, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF PnniNodeId, PnniPortId, pnniIfEntry FROM PNNI-MIB AtmAddr, AtmConnCastType, AtmConnKind, AtmServiceCategory, AtmVcIdentifier, AtmVpIdentifier, AtmTrafficDescrParamIndex FROM ATM-TC-MIB InterfaceIndex, InterfaceIndexOrZero FROM IF-MIB NetworkEntityNetworkServiceCategory, ResourcePartitionNetworkServiceCategory, PolicyConstraintIndex FROM ATM-POLICY-CONSTRAINT-MIB MplsLabel FROM MPLS-TC-STD-MIB; atmTraceMIB MODULE-IDENTITY LAST-UPDATED "200402061200Z" ORGANIZATION "The ATM Forum." CONTACT-INFO "The ATM Forum 2570 West El Camino Real, Suite 304 Mountain View, CA 94040-1313 USA Phone: +1 650-949-6700 Fax: +1 415-949-6705 info@atmforum.com" DESCRIPTION "The MIB module for ATM path and connection trace." REVISION "200402061200Z" DESCRIPTION "Addition of objects to support tracing of Policy Routing and ATM-MPLS Network Interworking related information." REVISION "0002220000Z" DESCRIPTION "Initial version of the MIB for ATM path and connection trace." ::= { atmfTrace 1 } atmForum OBJECT IDENTIFIER ::= { enterprises 353 } atmForumNetworkManagement OBJECT IDENTIFIER ::= { atmForum 5 } atmfSignalling OBJECT IDENTIFIER ::= { atmForumNetworkManagement 9 } atmfTrace OBJECT IDENTIFIER ::= { atmfSignalling 2 } atmTraceMIBObjects OBJECT IDENTIFIER ::= { atmTraceMIB 1 } -- Textual Conventions CallReference ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The 24-bit Call Reference used by signalling to identify a connection. The Call Reference is structured in two parts. The most significant bit represents the Call Reference Flag and the 23 least significant bits represent the Call Reference Value. For the same call, the Call Reference Value is identical on both sides of an interface while the Call Reference Flag is different. For the side originating the Call Reference, the Call Reference Flag is set to '0' while it is set to '1' for the side not originating the Call Reference. The distinguished value zero indicates that no Call Reference value was returned in the trace transit list." REFERENCE "ITU-T Recommendation Q.2931 Section 4.3" SYNTAX Integer32 (0..16777215) AtmEndPointReference ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "For point-to-multipoint SVCs and the switched connection legs of point-to-multipoint Soft PVCs, the 16-bit Endpoint Reference used by signalling to identify a leaf of the point-to-multipoint connection. The Endpoint Reference is structured in two parts. The most significant bit represents the Endpoint Reference Flag and the 15 least significant bits represent the Endpoint Reference Value. For the same call and leaf, the Endpoint Reference Value is identical on both sides of an interface while the Endpoint Reference Flag is different. For the side originating the endpoint reference, the Endpoint Reference Flag is set to '0' while it is set to '1' for the side not originating the Endpoint Reference. For the permanent connection legs at the root of point-to-multipoint Soft PVCs, the value used to identify a leaf in the atmSoftPVccLeafReference object or the atmSoftPVpcLeafReference object from the ATM-SOFT-PVC-MIB. For the permanent connection legs at the leaf end of point-to-multipoint Soft PVCs, the value 1 shall be used (consistent with the values used for atmSoftPVccLeafReference and atmSoftPVpcLeafReference in the ATM-SOFT-PVC-MIB). The distinguished value -1 indicates that no Endpoint Reference value was returned in the Trace transit list." REFERENCE "ITU-T Recommendation Q.2971 Section 8.2.1, ATM Forum PNNI v1.0 Addendum (Soft PVC MIB), af-pnni-0066.000" SYNTAX Integer32 (-1..65535) AtmTraceRecordIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of this object identifies a row in the atmTraceRecordTable. The distinguished value zero signifies that no row has been identified." SYNTAX Integer32 (0..2147483647) AtmTraceOwnerString ::= TEXTUAL-CONVENTION DISPLAY-HINT "255a" STATUS current DESCRIPTION "This data type is used to model an administratively assigned name of the owner of a resource. This information is taken from the NVT ASCII character set. It is suggested that this name contain one or more of the following: ASCII form of the manager station's transport address, management station name (e.g., domain name), network management personnel's name, location, or phone number. In some cases the agent itself will be the owner of an entry. In these cases, this string shall be set to a string starting with 'monitor'. SNMP access control is articulated entirely in terms of the contents of MIB views; access to a particular SNMP object instance depends only upon its presence or absence in a particular MIB view and never upon its value or the value of related object instances. Thus, objects of this type afford resolution of resource contention only among cooperating managers; they realize no access control function with respect to uncooperative parties." SYNTAX OCTET STRING (SIZE(0..127)) -- This MIB contains six tables and a number of scalars. The tables -- are: -- Trace Connection Table - trigger connection trace -- Trace Path Test Table - trigger a test connection or party -- Trace Path Filter Table - trigger path trace by filtering calls -- Trace Filter Record Table - correlate records with filters -- Trace Record Table - overall info about a connection or party -- Trace Info Table - detailed trace info for a connection or party -- Trace Interface Table - specify certain PNNI interfaces as -- trace destination interfaces atmTraceBaseGroup OBJECT IDENTIFIER ::= {atmTraceMIBObjects 1} atmTraceFilterControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object enables or disables the path trace filtering feature in the ATM device. When this object is modified from 'enable' to 'disable' the records in the atmTraceRecordTable are not removed but filtering is stopped in the device." DEFVAL { disable } ::= { atmTraceBaseGroup 1 } atmTraceMaxConcurrentRequests OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of concurrent active path or connection trace requests (i.e., connections or parties for which trace information gathering has been initiated, but for which no reply has been received yet) that are allowed by the agent. A value of 0 for this object implies that there is no limit on the number of concurrent active requests." ::= { atmTraceBaseGroup 2 } atmTraceAvailableRequests OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of new path or connection trace requests that can be initiated on the agent at this moment in time. This is equal to the maximum number of concurrent active path or connection trace requests that are allowed by the agent (i.e., atmTraceMaxConcurrentRequests), minus the current number of active path or connection trace requests." ::= { atmTraceBaseGroup 3 } atmTraceTransitListMaximumSize OBJECT-TYPE SYNTAX Integer32 (1466..65535) UNITS "octets" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum size in octets of the Trace transit list information element generated in any signalling message." DEFVAL { 1466 } ::= { atmTraceBaseGroup 4 } atmTraceConnGroup OBJECT IDENTIFIER ::= { atmTraceMIBObjects 2 } atmTraceConnTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTraceConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table whose entries describe existing connections and parties to be traced or in the process of being traced." ::= { atmTraceConnGroup 1 } atmTraceConnEntry OBJECT-TYPE SYNTAX AtmTraceConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table specifies an existing connection or party to be traced, in the process of being traced, or that has recently been traced. The results of the connection trace are returned in the atmTraceRecordTable and the atmTraceInfoTable. A management station wishing to create an entry should first create the associated instance of the row status and row owner objects, using a value of atmTraceConnIndex that is not currently in use. It must also, either in the same or in successive PDUs, create the associated instance of the objects that identify the connection to be traced. It should also modify the default values for the other configuration objects if the defaults are not appropriate. Once the appropriate instances of all the configuration objects have been created, either by an explicit SNMP set request or by default, the row status should be set to active to initiate the request. Note that this entire procedure may be initiated via a single set request which specifies a row status of createAndGo as well as specifies valid values for the non-defaulted configuration objects. After the connection trace completes, the management station should retrieve the values of the status objects of interest from the atmTraceRecordTable, and should then delete the entry. In order to prevent old entries from clogging the table, entries will be aged out, but an entry will not be deleted within 5 minutes of the last activity." INDEX { atmTraceConnIndex } ::= { atmTraceConnTable 1 } AtmTraceConnEntry ::= SEQUENCE { atmTraceConnIndex Integer32, atmTraceConnOwner AtmTraceOwnerString, atmTraceConnTraceSourceIf InterfaceIndex, atmTraceConnOrigConnType INTEGER, atmTraceConnOrigVpi AtmVpIdentifier, atmTraceConnOrigVci AtmVcIdentifier, atmTraceConnEndPtRef AtmEndPointReference, atmTraceConnCallRef CallReference, atmTraceConnOrigDlci Integer32, atmTraceConnOrigDirection INTEGER, atmTraceConnTraceConnId TruthValue, atmTraceConnTraceCallRef TruthValue, atmTraceConnPassAlongRequest TruthValue, atmTraceConnFailTimeout Integer32, atmTraceConnAgeTimeout Integer32, atmTraceConnRestart INTEGER, atmTraceConnTrapOnCompletion TruthValue, atmTraceConnRecordIndex AtmTraceRecordIndex, atmTraceConnRowStatus RowStatus, atmTraceConnTraceNeNsc TruthValue, atmTraceConnTraceRpNsc TruthValue, atmTraceConnTraceIncoming TruthValue, atmTraceConnTraceLabels TruthValue } atmTraceConnIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer uniquely identifying a connection trace request." ::= { atmTraceConnEntry 1 } atmTraceConnOwner OBJECT-TYPE SYNTAX AtmTraceOwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry." ::= { atmTraceConnEntry 2 } atmTraceConnTraceSourceIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The interface at which the connection trace is originated. This object must be specified." ::= { atmTraceConnEntry 3 } atmTraceConnOrigConnType OBJECT-TYPE SYNTAX INTEGER { other(1), atmVcc(2), atmVpc(3), atmCOBISigConn(4), frameRelayVc(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of connection at the trace source interface." DEFVAL { atmVcc } ::= { atmTraceConnEntry 4 } atmTraceConnOrigVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the VPI value of the existing connection on the trace source interface. This object only applies when atmTraceConnOrigConnType is set to 'atmVcc' or 'atmVpc'. When this is the case, either this object or atmTraceConnCallRef must be specified. When the atmTraceConnCallRef object is specified, this object may not be set." ::= { atmTraceConnEntry 5 } atmTraceConnOrigVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the VCI value of the existing connection on the trace source interface. This object only applies when atmTraceConnOrigConnType is set to 'atmVcc'. When this is the case, either this object or atmTraceConnCallRef must be specified. When the atmTraceConnCallRef object is specified, this object may not be set." ::= { atmTraceConnEntry 6 } atmTraceConnEndPtRef OBJECT-TYPE SYNTAX AtmEndPointReference MAX-ACCESS read-create STATUS current DESCRIPTION "The Endpoint Reference value identifying a leaf of an existing point-to-multipoint connection. This object does not apply when the connection is not a point- to-multipoint connection." ::= { atmTraceConnEntry 7 } atmTraceConnCallRef OBJECT-TYPE SYNTAX CallReference MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the call reference value of the existing connection on the trace source interface. For CO-BI connections, the value of this object must be specified. For other types of connections, either this object or the connection identifier objects (atmTraceConnOrigVpi, atmTraceConnOrigVpi and atmTraceConnOrigVci, or atmTraceConnOrigDlci, as appropriate for the connection type) must be specified. When any of atmTraceConnOrigVpi, atmTraceConnOrigVci, or atmTraceConnOrigDlci are specified, this object may not be set." ::= { atmTraceConnEntry 8 } atmTraceConnOrigDlci OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the DLCI value of the existing connection on the trace source interface. This object only applies when atmTraceConnOrigConnType is set to 'frameRelayVc'. When this is the case, either this object or atmTraceConnCallRef must be specified. When the atmTraceConnCallRef object is specified, this object may not be set." ::= { atmTraceConnEntry 9 } atmTraceConnOrigDirection OBJECT-TYPE SYNTAX INTEGER { incoming(1), outgoing(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the connection trace is to proceed in the incoming direction from the trace source interface, or in the outgoing direction from the trace source interface." DEFVAL { incoming } ::= { atmTraceConnEntry 10 } atmTraceConnTraceConnId OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the connection trace shall include connection identifier (e.g. VPI/VCI, DLCI) information." DEFVAL { false } ::= { atmTraceConnEntry 11 } atmTraceConnTraceCallRef OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the connection trace shall include call reference information, and endpoint reference information for point-to-multipoint connections." DEFVAL { false } ::= { atmTraceConnEntry 12 } atmTraceConnPassAlongRequest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the 'pass along request' bit shall be set in the Trace transit list information element. When this object is set to 'true' and systems that do not support connection trace are present in the network, gaps may occur between successive entries in the atmTraceInfoTable identifying logical nodes and logical ports traversed by this connection or party." DEFVAL { true } ::= { atmTraceConnEntry 13 } atmTraceConnFailTimeout OBJECT-TYPE SYNTAX Integer32 (0..100) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds left before the connection trace is declared to have failed. After this timer expires the value of this object will be zero and the atmTraceConnRecordIndex will also remain at zero. If the timer expires and atmTraceConnTrapOnCompletion is set to 'true', an atmTraceConnCompletion trap will be generated." DEFVAL { 30 } ::= { atmTraceConnEntry 14 } atmTraceConnAgeTimeout OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds left for this entry to age out. On expiry of this timer the display records in the atmTraceRecordTable and atmTraceInfoTable corresponding to this entry are deleted, as well as the atmTraceConnEntry. When the management station modifies this object, the currently running timer, if any, is aborted and a timer is started with the new value of this object. The value '-1' will indicate an infinite timeout value. " DEFVAL { 600 } ::= { atmTraceConnEntry 15 } atmTraceConnRestart OBJECT-TYPE SYNTAX INTEGER { restart(1), noop(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When the value is set to 'restart', the record for this connection trace is cleared and the connection trace is initiated. When the value is set to 'noop' no operation is performed. When read, the value 'noop' is returned." DEFVAL { noop } ::= { atmTraceConnEntry 16 } atmTraceConnTrapOnCompletion OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether an atmTraceConnCompletion trap shall be issued on completion of the connection trace. If such a trap is desired, it is the responsibility of the management entity to ensure that the SNMP administrative model is configured in such a way as to allow the trap to be delivered." DEFVAL { false } ::= { atmTraceConnEntry 17 } atmTraceConnRecordIndex OBJECT-TYPE SYNTAX AtmTraceRecordIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the row in the atmTraceRecordTable that was generated by this connection trace. The distinguished value zero indicates that no reply has been received yet or that no reply was received before expiry of atmTraceConnFailTimeout, so no record has been generated." ::= { atmTraceConnEntry 18 } atmTraceConnRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create and delete entries in this table. When a row is activated, a connection trace is initiated." ::= { atmTraceConnEntry 19 } atmTraceConnTraceNeNsc OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the connection trace shall include Ne-NSCs supporting the connection ." DEFVAL { false } ::= { atmTraceConnEntry 20 } atmTraceConnTraceRpNsc OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the connection trace shall include Rp-NSCs supporting the connection." DEFVAL { false } ::= { atmTraceConnEntry 21 } atmTraceConnTraceIncoming OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the connection trace shall record the NSCs supporting the connection at the incoming interface of the nodes. If this value is set to true and the atmTraceConnTraceNeNsc object is also true, then the trace shall include the list of Ne-NSCs supporting the connection at the incoming interface of the nodes. If this value is set to true and the atmTraceConnTraceRpNsc object is also true, then the trace shall include the list of Rp-NSCs supporting the connection at the incoming interface of the nodes. If this value is set to false, then the trace shall not record the NSCs supporting the connection at the incoming interface of the nodes." DEFVAL { false } ::= { atmTraceConnEntry 22 } atmTraceConnTraceLabels OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the connection trace shall include interworking LSP labels, if applicable." DEFVAL { false } ::= { atmTraceConnEntry 23 } atmTracePathTestGroup OBJECT IDENTIFIER ::= { atmTraceMIBObjects 3 } atmTracePathTestTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTracePathTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table whose entries describe test connections and parties initiated to determine paths across the network. Typically these connections and parties are cleared when the trace destination node is reached, but the entry may be configured to leave the connections up using the atmTracePathTestClearCallAtTDest object." ::= { atmTracePathTestGroup 1 } atmTracePathTestEntry OBJECT-TYPE SYNTAX AtmTracePathTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table specifies a test connection or test party that is initiated in order to determine a path across the network. Typically the connection or party is cleared when the trace destination node is reached, but the entry may be configured to leave the connections up using the atmTracePathTestClearCallAtTDest object. The results of the path trace are returned in the atmTraceFilterRecordTable, the atmTraceRecordTable, and the atmTraceInfoTable. A management station wishing to create an entry should first create the associated instance of the row status and row owner objects, using a value of atmTracePathTestIndex that is not currently in use. It must also, either in the same or in successive PDUs, create the associated instance of the address objects. It should also modify the default values for the other configuration objects if the defaults are not appropriate. Once the appropriate instance of all the configuration objects have been created, either by an explicit SNMP set request or by default, the row status should be set to active to initiate the request. Note that this entire procedure may be initiated via a single set request which specifies a row status of createAndGo as well as specifies valid values for the non-defaulted configuration objects. After the test connection or party completes, the management station should retrieve the values of the status objects of interest from the atmTraceRecordTable, and should then delete the entry. In order to prevent old entries from clogging the table, entries will be aged out, but an entry will not be deleted within 5 minutes of completing." INDEX { atmTracePathTestIndex } ::= { atmTracePathTestTable 1 } AtmTracePathTestEntry ::= SEQUENCE { atmTracePathTestIndex Integer32, atmTracePathTestOwner AtmTraceOwnerString, atmTracePathTestConnType INTEGER, atmTracePathTestConnCastType AtmConnCastType, atmTracePathTestTraceSourceIf InterfaceIndex, atmTracePathTestP2MpNewConn TruthValue, atmTracePathTestOrigVpi AtmVpIdentifier, atmTracePathTestOrigVci AtmVcIdentifier, atmTracePathTestCalledParty AtmAddr, atmTracePathTestCallingParty AtmAddr, atmTracePathTestRxTrafDescrIndex AtmTrafficDescrParamIndex, atmTracePathTestTxTrafDescrIndex AtmTrafficDescrParamIndex, atmTracePathTestClearCallAtTDest TruthValue, atmTracePathTestTraceCrankback TruthValue, atmTracePathTestTraceConnId TruthValue, atmTracePathTestTraceCallRef TruthValue, atmTracePathTestPassAlongRequest TruthValue, atmTracePathTestAgeTimeout Integer32, atmTracePathTestRestart INTEGER, atmTracePathTestTrapOnCompletion TruthValue, atmTracePathTestRecordIndex AtmTraceRecordIndex, atmTracePathTestRowStatus RowStatus, atmTracePathTestTraceNeNsc TruthValue, atmTracePathTestTraceRpNsc TruthValue, atmTracePathTestTraceIncoming TruthValue, atmTracePathTestPolicyConstraint PolicyConstraintIndex, atmTracePathTestTraceLabels TruthValue } atmTracePathTestIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer uniquely identifying a test connection or test party." ::= { atmTracePathTestEntry 1 } atmTracePathTestOwner OBJECT-TYPE SYNTAX AtmTraceOwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry." ::= { atmTracePathTestEntry 2 } atmTracePathTestConnType OBJECT-TYPE SYNTAX INTEGER { other(1), atmVcc(2), atmVpc(3), atmCOBISigConn(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the test connection is a virtual channel connection, a virtual path connection, or a connection- oriented bearer-independent signalling connection." DEFVAL { atmVcc } ::= { atmTracePathTestEntry 3 } atmTracePathTestConnCastType OBJECT-TYPE SYNTAX AtmConnCastType MAX-ACCESS read-create STATUS current DESCRIPTION "The connection topology type (e.g. point-to-point or point-to-multipoint) of the test connection or party." DEFVAL { p2p } ::= { atmTracePathTestEntry 4 } atmTracePathTestTraceSourceIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The interface at which the test connection or test party is originated." ::= { atmTracePathTestEntry 5 } atmTracePathTestP2MpNewConn OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the test party for a point-to-multipoint connection is initiated on an existing branch (indicated by setting this object to 'false') or whether it is the first party of a new connection (indicated by setting this object to 'true'). This object does not apply when atmTracePathTestConnCastType is set to 'p2p'." DEFVAL { false } ::= { atmTracePathTestEntry 6 } atmTracePathTestOrigVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "When atmTracePathTestConnCastType is set to 'p2mpRoot' and atmTracePathTestP2MpNewConn is set to 'false' (i.e. path trace of a new party on an existing connection is requested), this object indicates the VPI value of the existing connection on the trace source interface. When atmTracePathTestClearCallAtTDest is set to 'true' and either - atmTracePathTestConnCastType is 'p2p', or - atmTracePathTestConnCastType is 'p2mpRoot' and atmTracePathTestP2MpNewConn is set to 'true', this object is not applicable. When atmTracePathTestClearCallAtTDest is set to 'false', this object indicates the VPI value to be used for the active connection. Note that if the VPI/VCI can be assigned at the other side of the interface, there may be some possibility of VPI/VCI collision for SETUP messages received on this interface, when the other side of the interface does not know that this VPI/VCI value is being used." DEFVAL { 0 } ::= { atmTracePathTestEntry 7 } atmTracePathTestOrigVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "When atmTracePathTestConnCastType is set to 'p2mpRoot' and atmTracePathTestP2MpNewConn is set to 'false' (i.e. path trace of a new party on an existing connection is requested), this object indicates the VCI value of the existing connection on the trace source interface. When atmTracePathTestClearCallAtTDest is set to 'true' and either - atmTracePathTestConnCastType is 'p2p', or - atmTracePathTestConnCastType is 'p2mpRoot' and atmTracePathTestP2MpNewConn is set to 'true', this object is not applicable. When atmTracePathTestClearCallAtTDest is set to 'false', this object indicates the VCI value to be used for the active connection. Note that if the VPI/VCI can be assigned at the other side of the interface, there may be some possibility of VPI/VCI collision for SETUP messages received on this interface, when the other side of the interface does not know that this VPI/VCI value is being used. If atmTracePathTestConnType is set to a value other than 'atmVcc', this value is set to zero." DEFVAL { 0 } ::= { atmTracePathTestEntry 8 } atmTracePathTestCalledParty OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The called party number towards which the test connection or test party is to be initiated." ::= { atmTracePathTestEntry 9 } atmTracePathTestCallingParty OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The calling party number used for the test connection or test party." DEFVAL { "" } ::= { atmTracePathTestEntry 10 } atmTracePathTestRxTrafDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the receive direction of this test connection (from the point of view of the trace source interface). This object does not apply when the value of atmTracePathTestP2MpNewConn is 'false'." DEFVAL { 0 } ::= { atmTracePathTestEntry 11 } atmTracePathTestTxTrafDescrIndex OBJECT-TYPE SYNTAX AtmTrafficDescrParamIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this test connection (from the point of view of the trace source interface). This object does not apply when the value of atmTracePathTestP2MpNewConn is 'false'." DEFVAL { 0 } ::= { atmTracePathTestEntry 12 } atmTracePathTestClearCallAtTDest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the test connection or party shall be cleared when the trace destination node is reached. When this is set to 'false', the test connection/party shall be cleared when the entry is deleted using the atmTracePathTestRowStatus object." DEFVAL { true } ::= { atmTracePathTestEntry 13 } atmTracePathTestTraceCrankback OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include crankback information. When this is set to false, as a consequence of the signalling procedures for path trace, trace information will only be returned if the connection or party succeeds." DEFVAL { false } ::= { atmTracePathTestEntry 14 } atmTracePathTestTraceConnId OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include connection identifier (e.g. VPI/VCI, DLCI) information." DEFVAL { false } ::= { atmTracePathTestEntry 15 } atmTracePathTestTraceCallRef OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include call reference information, and endpoint reference information for point-to-multipoint connections." DEFVAL { false } ::= { atmTracePathTestEntry 16 } atmTracePathTestPassAlongRequest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the 'pass along request' bit shall be set in the Trace transit list information element. When this object is set to 'true' and systems that do not support path trace are present in the network, gaps may occur between successive entries in the atmTraceInfoTable identifying logical nodes and logical ports traversed by this connection or party. When this object is set to 'false', trace information might not be returned unless all systems along the path support the path trace functionality." DEFVAL { true } ::= { atmTracePathTestEntry 17 } atmTracePathTestAgeTimeout OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds left for this entry to age out. On expiry of this timer the display records in the atmTraceRecordTable and the atmTraceInfoTable corresponding to this entry are deleted, as well as the atmTracePathTestEntry. When the management station modifies this object, the currently running timer, if any, is aborted and a timer is started with the new value of this object. The value '-1' will indicate an infinite timeout value. " DEFVAL { 600 } ::= { atmTracePathTestEntry 18 } atmTracePathTestRestart OBJECT-TYPE SYNTAX INTEGER { restart(1), noop(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When the value is set to 'restart', the test record for this connection is cleared and the test connection or party is initiated. When the value is set to 'noop' no operation is performed. When read, the value 'noop' is returned." DEFVAL { noop } ::= { atmTracePathTestEntry 19 } atmTracePathTestTrapOnCompletion OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether an atmTracePathTestCompletion trap shall be issued on completion of the path trace. If such a trap is desired, it is the responsibility of the management entity to ensure that the SNMP administrative model is configured in such a way as to allow the trap to be delivered." DEFVAL { false } ::= { atmTracePathTestEntry 20 } atmTracePathTestRecordIndex OBJECT-TYPE SYNTAX AtmTraceRecordIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the row in the atmTraceRecordTable that was generated by this test connection or party. The distinguished value zero indicates that no reply has been received yet, so no record has been generated." ::= { atmTracePathTestEntry 21 } atmTracePathTestRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create and delete entries in this table. When a row is activated, a test connection or test party is initiated. When the row is deleted, the test connection or test party is cleared (if it has not already been cleared) and the corresponding entry in the atmTraceRecordTable is deleted." ::= { atmTracePathTestEntry 22 } atmTracePathTestTraceNeNsc OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include Ne-NSCs supporting the connection." DEFVAL { false } ::= { atmTracePathTestEntry 23 } atmTracePathTestTraceRpNsc OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include Rp-NSCs supporting the connection." DEFVAL { false } ::= { atmTracePathTestEntry 24 } atmTracePathTestTraceIncoming OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include the NSCs supporting the connection at the incoming interface of the nodes. If this value is set to true and the atmTracePathtestTraceNeNsc object is also true, then the trace shall include the list of Ne-NSCs supporting the connection at the incoming interface of the nodes. If this value is set to true and the atmTracePathTestTraceRpNsc object is also true, then the trace shall include the list of Rp-NSCs supporting the connection at the incoming interface of the nodes. If this value is set to false, then the trace shall not record the NSCs supporting the connection at the incoming interface of the nodes." DEFVAL { false } ::= { atmTracePathTestEntry 25 } atmTracePathTestPolicyConstraint OBJECT-TYPE SYNTAX PolicyConstraintIndex MAX-ACCESS read-create STATUS current DESCRIPTION "Defines the row of the policyConstraintTable that specifies the policy constraint to be used for the establishment of the test connection." DEFVAL { 0 } ::= { atmTracePathTestEntry 26 } atmTracePathTestTraceLabels OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include interworking LSP labels, if applicable." DEFVAL { false } ::= { atmTracePathTestEntry 27 } atmTraceFilterGroup OBJECT IDENTIFIER ::= { atmTraceMIBObjects 4 } atmTraceFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTraceFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table whose entries describe the filtering criteria for recording of path trace information." ::= { atmTraceFilterGroup 1 } atmTraceFilterEntry OBJECT-TYPE SYNTAX AtmTraceFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table corresponds to a filtering criteria based on which path trace is initiated for connections and parties in the process of being established. This selection criteria is applied against all connections and parties generated or detectedat this ATM device. Only connections and parties being established which match against all of the entry's criteria are recorded in the atmTraceRecordTable. A new entry can be created by specifying a atmTraceFilterIndex value that is currently not being used and also using an appropriate value (createAndGo or createAndWait) for the atmTraceFilterRowStatus object. If a particular connection or party matches multiple entries in the atmTraceFilterTable then multiple entries will be created in the atmTraceRecordTable for each of the matched entries in the atmTraceFilterTable." INDEX { atmTraceFilterIndex } ::= { atmTraceFilterTable 1 } AtmTraceFilterEntry ::= SEQUENCE { atmTraceFilterIndex Integer32, atmTraceFilterOwner AtmTraceOwnerString, atmTraceFilterConnKind BITS, atmTraceFilterConnCastType BITS, atmTraceFilterServiceCategory BITS, atmTraceFilterInIf InterfaceIndexOrZero, atmTraceFilterOutIf InterfaceIndexOrZero, atmTraceFilterCallingPartyPrefix AtmAddr, atmTraceFilterCallingPartyLength Integer32, atmTraceFilterCalledPartyPrefix AtmAddr, atmTraceFilterCalledPartyLength Integer32, atmTraceFilterClearCallAtTDest TruthValue, atmTraceFilterTraceCrankback TruthValue, atmTraceFilterTraceConnId TruthValue, atmTraceFilterTraceCallRef TruthValue, atmTraceFilterPassAlongRequest TruthValue, atmTraceFilterMaxRecords Integer32, atmTraceFilterRecordCountDown Integer32, atmTraceFilterStopTimeout Integer32, atmTraceFilterAgeTimeout Integer32, atmTraceFilterPurge INTEGER, atmTraceFilterTrapEnable TruthValue, atmTraceFilterNumMatches Counter32, atmTraceFilterRowStatus RowStatus, atmTraceFilterPolicy TruthValue, atmTraceFilterTraceNeNsc TruthValue, atmTraceFilterTraceRpNsc TruthValue, atmTraceFilterTraceIncoming TruthValue, atmTraceFilterTraceLabels TruthValue } atmTraceFilterIndex OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer uniquely identifying a filtering criteria." ::= { atmTraceFilterEntry 1 } atmTraceFilterOwner OBJECT-TYPE SYNTAX AtmTraceOwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry." ::= { atmTraceFilterEntry 2 } atmTraceFilterConnKind OBJECT-TYPE SYNTAX BITS { other(0), svcAndSpvcNotInitiator(1), spvcInitiator(2), svpAndSpvpNotInitiator(3), spvpInitiator(4), atmCOBISigConn(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object enables the user to track the paths of switched virtual channel/path connections, soft permanent virtual channel/path connections initiated by this node, and soft permanent virtual channel/path connections initiated by other nodes." ::= { atmTraceFilterEntry 3 } atmTraceFilterConnCastType OBJECT-TYPE SYNTAX BITS { p2p(0), p2mp(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object restricts the scope of the filter based on the type of topology of connections (point-to-point or point-to-multipoint)." ::= { atmTraceFilterEntry 4 } atmTraceFilterServiceCategory OBJECT-TYPE SYNTAX BITS { cbr(0), rtVbr(1), nrtVbr(2), abr(3), ubr(4), gfr(5), other(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object restricts the scope of the filter to calls belonging to service categories represented by this object." ::= { atmTraceFilterEntry 5 } atmTraceFilterInIf OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This object restricts the scope of the filter to calls which enter the ATM device through the port represented by this object, or are initiated at this port (e.g. Soft PVCs). It has the value 0, or the ifIndex value of an ATM Interface. The value zero indicates that the scope of the filter is not restricted by the incoming port." DEFVAL { 0 } ::= { atmTraceFilterEntry 6 } atmTraceFilterOutIf OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This object restricts the scope of the filter to calls which exit the ATM device through the port represented by this object. It has the value 0, or the ifIndex value of an ATM interface. The value zero indicates that the scope of the filter is not restricted by the outgoing port." DEFVAL { 0 } ::= { atmTraceFilterEntry 7 } atmTraceFilterCallingPartyPrefix OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The combination of this object and the corresponding instance of atmTraceFilterCallingPartyLength is one selection criteria for this record. To match this selection criteria, a connection setup must have a Calling Party Address which has an initial part (of length atmTraceFilterCalledPartyLength bits) equal in value to atmTraceFilterCallingParty. When the default value for the object is retained then the call will match this filtering criteria for any calling address in the call, or if the calling party number is not present in the call. The value must be padded with zeros from atmTraceFilterCallingPartyLength to the full length of the address (8 octets for E.164 numbers and 20 octets for AESAs)." DEFVAL { "" } ::= { atmTraceFilterEntry 8 } atmTraceFilterCallingPartyLength OBJECT-TYPE SYNTAX Integer32 (1..160) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the number of bits in atmTraceFilterCallingParty that shall be used when matching against the calling party of a new call setup." DEFVAL { 152 } ::= { atmTraceFilterEntry 9 } atmTraceFilterCalledPartyPrefix OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The combination of this object and the corresponding instance of atmTraceFilterCalledPartyLength is one selection criteria for this record. To match this selection criteria, a connection setup must have a called party address which has an initial part (of length atmTraceFilterCalledPartyLength bits) equal in value to atmTraceFilterCalledParty. When the default value for the object is retained then the call will match this filtering criteria for any called address in the call. The value must be padded with zeros from atmTraceFilterCalledPartyLength to the full length of the address (8 octets for E.164 numbers and 20 octets for AESAs)." DEFVAL {""} ::= { atmTraceFilterEntry 10 } atmTraceFilterCalledPartyLength OBJECT-TYPE SYNTAX Integer32 (1..160) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the number of bits in atmTraceFilterCalledParty that shall be used when matching against the called party of a new call setup." DEFVAL { 152 } ::= { atmTraceFilterEntry 11 } atmTraceFilterClearCallAtTDest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the connection or party shall be cleared when the trace destination node is reached." DEFVAL { false } ::= { atmTraceFilterEntry 12 } atmTraceFilterTraceCrankback OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include crankback information. When this is set to false, as a consequence of the signalling procedures for path trace, trace information will only be returned if the connection or party succeeds." DEFVAL { false } ::= { atmTraceFilterEntry 13 } atmTraceFilterTraceConnId OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include connection identifier (e.g. VPI/VCI, DLCI) information." DEFVAL { false } ::= { atmTraceFilterEntry 14 } atmTraceFilterTraceCallRef OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include call reference information, and endpoint reference information for point-to-multipoint connections." DEFVAL { false } ::= { atmTraceFilterEntry 15 } atmTraceFilterPassAlongRequest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the 'pass along request' bit shall be set in the Trace transit list information element. When this object is set to 'true' and systems that do not support path trace are present in the network, gaps may occur between successive entries in the atmTraceInfoTable identifying logical nodes and logical ports traversed by this connection or party. When this object is set to 'false', trace information might not be returned unless all systems along the path support the path trace functionality." DEFVAL { true } ::= { atmTraceFilterEntry 16 } atmTraceFilterMaxRecords OBJECT-TYPE SYNTAX Integer32 (-1..214783647) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of entries that are desired in the atmTraceRecordTable on behalf of this filter. The agent will not create more than this number of entries in the table, but may choose to further limit the number of entries for this filter in the atmTraceRecordTable for any reason including the lack of resources. The agent will however dedicate resources for a minimum number of entries in the atmTraceRecordTable, to take care of temporary memory allocation failures in the system. In case of memory allocation failures the agent will utilize these dedicated resources for the creation of the new entries. If memory resource failures continue and the dedicated resources are exhausted then the records in the atmTraceRecordTable are pruned such that the oldest entries are removed to make way for the new entries. A value '-1' will indicate no upper limit for the number of records stored. The manager can set this object to -1 if overwriting of records is not desired. The new value for this object will take effect immediately. If this object is set to a value less than the number of entries that is currently present in the atmTraceRecordTable corresponding to this entry, then the oldest entries in the atmTraceRecordTable will be deleted so that their number equals the new value of this object. If the value of this object is changed from -1 to any other positive value then the entries will be pruned such that only the first n records collected for this entry are retained in the atmTraceRecordTable, n being the new value of this object." DEFVAL { 20 } ::= { atmTraceFilterEntry 17 } atmTraceFilterRecordCountDown OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of entries left to be collected in the atmTraceRecordTable before filtering is disabled for this entry. The display records in the atmTraceRecordTable corresponding to this entry are retained. The management station can restart filtering for this entry by setting this object to a positive value (subject to atmTraceFilterRowStatus being 'active' and atmTraceFilterStopTimeout having a positive value or being set to '-1'). When the object is set to zero, filtering is stopped for this entry. When the management station modifies this object, the current value is replaced and the agent counts down from the new value of this object. The value '-1' indicates that filtering will not be automatically disabled based on the number of entries collected in the atmTraceRecordTable." DEFVAL { -1 } ::= { atmTraceFilterEntry 18 } atmTraceFilterStopTimeout OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds left for this entry to collect records. On expiry of this timer filtering is disabled for this entry. The display records in the atmTraceRecordTable corresponding to this entry are retained. When the timer expires the object will have a value zero. The management station can restart filtering for this entry by setting this object to a positive value (subject to atmTraceFilterRowStatus being 'active' and atmTraceFilterRecordCountDown having a positive value or being set to '-1'). When the object is set to zero, filtering is stopped for this entry. When the management station modifies this object, the currently running timer, if any, is aborted and a timer is started with the new value of this object. The value '-1' will indicate an infinite timeout value." DEFVAL { 600 } ::= { atmTraceFilterEntry 19 } atmTraceFilterAgeTimeout OBJECT-TYPE SYNTAX Integer32 (-1..2147483647) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds left for this entry to age out. On expiry of this timer the display records in the atmTraceFilterRecordTable, atmTraceRecordTable and the atmTraceInfoTable corresponding to this entry are deleted, as well as the atmTraceFilterEntry. When the management station modifies this object, the currently running timer, if any, is aborted and a timer is started with the new value of this object. The value '-1' will indicate an infinite timeout value. " DEFVAL { 600 } ::= { atmTraceFilterEntry 20 } atmTraceFilterPurge OBJECT-TYPE SYNTAX INTEGER { purge(1), noop(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The object provides a facility for the user to purge the records in the atmTraceRecordTable corresponding to this entry. When the value is set to 'purge', the records in the atmTraceRecordTable corresponding to this entry are purged. When the value is set to 'noop' no operation is performed. When read, the value 'noop' is returned." DEFVAL { noop } ::= { atmTraceFilterEntry 21 } atmTraceFilterTrapEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether an atmTraceFilterTrap shall be issued the next time a record is added to the atmTraceRecordTable and the atmTraceFilterRecordTable corresponding to this filter. This object automatically resets itself to 'false' each time a trap is generated for this filter. This object must be reset to 'true' before another atmTracePathFilter trap can be generated for this filter entry. If such a trap is desired, it is the responsibility of the management entity to ensure that the SNMP administrative model is configured in such a way as to allow the trap to be delivered." DEFVAL { false } ::= { atmTraceFilterEntry 22 } atmTraceFilterNumMatches OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A monotonically increasing counter to keep track of the number of calls or parties that matched this entry for the entire lifetime of this entry. " ::= { atmTraceFilterEntry 23 } atmTraceFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the status of this row. Used according to the row installation and removal conventions. This object can be used to temporarily inactivate an entry in the table. When this object is set to a value 'notInService' filtering is stopped for the corresponding row. Any records that have been stored in the atmTraceRecordTable and the atmTraceFilterRecordTable corresponding to this entry will not be released. Any writeable objects in the row can be modified when the row is active. All values will take effect immediately. When this object is set to 'destroy', all corresponding records in the atmTraceFilterRecordTable and the atmTraceRecordTable are deleted." ::= { atmTraceFilterEntry 24 } atmTraceFilterPolicy OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object restricts the scope of the filter to connection setups that include a Policy constraint information element." DEFVAL { false } ::= { atmTraceFilterEntry 25 } atmTraceFilterTraceNeNsc OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include Ne-NSCs supporting the connection." DEFVAL { false } ::= { atmTraceFilterEntry 26 } atmTraceFilterTraceRpNsc OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include Rp-NSCs supporting the connection." DEFVAL { false } ::= { atmTraceFilterEntry 27 } atmTraceFilterTraceIncoming OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include the NSCs supporting the connection at the incoming interface of the nodes. If this value is set to true and the atmTraceFilterTraceNeNsc object is also true, then the trace shall include the list of Ne-NSCs supporting the connection at the incoming interface of the nodes. If this value is set to true and the atmTraceFilterTraceRpNsc object is also true, then the trace shall include the list of Rp-NSCs supporting the connection at the incoming interface of the nodes. If this value is set to false, then the trace shall not record the NSCs supporting the connection at the incoming interface of the nodes." DEFVAL { false } ::= { atmTraceFilterEntry 28 } atmTraceFilterTraceLabels OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the path trace shall include interworking LSP labels, if applicable." DEFVAL { false } ::= { atmTraceFilterEntry 29 } atmTraceFilterRecordTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTraceFilterRecordEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table that lists which trace records have been returned for which trace filters. This table also lists the connection characteristics for each connection record, other than those values returned in the Trace transit list information element." ::= { atmTraceFilterGroup 2 } atmTraceFilterRecordEntry OBJECT-TYPE SYNTAX AtmTraceFilterRecordEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing the index of a record associated with a given trace filter. This table also lists some of the connection characteristics." INDEX { atmTraceFilterIndex, atmTraceFilterRecordIndex } ::= { atmTraceFilterRecordTable 1 } AtmTraceFilterRecordEntry ::= SEQUENCE { atmTraceFilterRecordIndex AtmTraceRecordIndex, atmTraceFilterRecordConnKind AtmConnKind, atmTraceFilterRecordConnCastType AtmConnCastType, atmTraceFilterRecordServiceCategory AtmServiceCategory, atmTraceFilterRecordInIf InterfaceIndex, atmTraceFilterRecordOutIf InterfaceIndexOrZero, atmTraceFilterRecordCallingParty AtmAddr, atmTraceFilterRecordCalledParty AtmAddr } atmTraceFilterRecordIndex OBJECT-TYPE SYNTAX AtmTraceRecordIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object identifies a row in the atmTraceRecordTable that was generated by the trace filter identified by atmTraceFilterIndex." ::= { atmTraceFilterRecordEntry 1 } atmTraceFilterRecordConnKind OBJECT-TYPE SYNTAX AtmConnKind MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the use of call control (e.g. switched virtual connection or soft permanent virtual connection) of the connection or party on the incoming interface." ::= { atmTraceFilterRecordEntry 2 } atmTraceFilterRecordConnCastType OBJECT-TYPE SYNTAX AtmConnCastType MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the type of topology of the connection (point-to-point or point-to-multipoint) on the incoming interface." ::= { atmTraceFilterRecordEntry 3 } atmTraceFilterRecordServiceCategory OBJECT-TYPE SYNTAX AtmServiceCategory MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the service category used by the call." ::= { atmTraceFilterRecordEntry 4 } atmTraceFilterRecordInIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The IfIndex of the incoming port on which this call was received by the ATM device." ::= { atmTraceFilterRecordEntry 5 } atmTraceFilterRecordOutIf OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The IfIndex of the outgoing port, if available, through which this call was routed to the network. The distinguished value zero indicates that the call was rejected before any outgoing interface was chosen." ::= { atmTraceFilterRecordEntry 6 } atmTraceFilterRecordCallingParty OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the ATM adddress of the calling party in the connection or party." ::= { atmTraceFilterRecordEntry 7 } atmTraceFilterRecordCalledParty OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the ATM address of the called party in the connection or party." ::= { atmTraceFilterRecordEntry 8 } atmTraceRecordGroup OBJECT IDENTIFIER ::= { atmTraceMIBObjects 5 } atmTraceRecordTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTraceRecordEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table and the atmTraceInfoTable are used to display the path or connection trace results. Trace information that is not repeated at each hop is shown in this table." ::= { atmTraceRecordGroup 1 } atmTraceRecordEntry OBJECT-TYPE SYNTAX AtmTraceRecordEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing a trace record for one new or existing connection or party." INDEX { atmTraceRecordIndex } ::= { atmTraceRecordTable 1 } AtmTraceRecordEntry ::= SEQUENCE { atmTraceRecordIndex AtmTraceRecordIndex, atmTraceRecordStatus INTEGER, atmTraceRecordCause Integer32, atmTraceRecordDiags OCTET STRING, atmTraceRecordTraceSourcePortId PnniPortId, atmTraceRecordTraceSourceDlci Integer32, atmTraceRecordTraceDestVpi AtmVpIdentifier, atmTraceRecordTraceDestVci AtmVcIdentifier, atmTraceRecordTraceDestCallRef CallReference, atmTraceRecordTraceDestEndPtRef AtmEndPointReference, atmTraceRecordTraceDestDlci Integer32, atmTraceRecordTimeStamp TimeStamp, atmTraceRecordTraceDestReceiveLabel MplsLabel, atmTraceRecordTraceDestTransmitLabel MplsLabel } atmTraceRecordIndex OBJECT-TYPE SYNTAX AtmTraceRecordIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to distinguish between multiple trace records. " ::= { atmTraceRecordEntry 1 } atmTraceRecordStatus OBJECT-TYPE SYNTAX INTEGER { traceInProgress(1), traceCompletedNormally(2), traceIncomplete(3), traceExceededIELengthLimitations(4), traceExceededMessageLengthLimitations(5), traceLackResource(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The returned trace status for this connection or party." ::= { atmTraceRecordEntry 2 } atmTraceRecordCause OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the reason for the call failure. When the call succeeds, the distinguished value zero is returned. When a PNNI Crankback information element is included in the last call clearing message, this object contains the crankback cause. In all other cases, the values are the same as the cause code values defined for the Cause information element." REFERENCE "ATM Forum's UNI3.0/3.1 Specification. " ::= { atmTraceRecordEntry 3 } atmTraceRecordDiags OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the contents of the diagnostics fields from the Cause information element. When the value of atmTraceRecordCause is 49, 'Quality of Service unavailable', the diagnostics are taken from the PNNI Crankback information element instead of the Cause information element." REFERENCE "ATM Forum's UNI3.0/3.1 Specification. " ::= { atmTraceRecordEntry 4 } atmTraceRecordTraceSourcePortId OBJECT-TYPE SYNTAX PnniPortId MAX-ACCESS read-only STATUS current DESCRIPTION "The PNNI logical port ID identifying the trace source interface. The distinguished value zero indicates that no trace source port ID was returned in the Trace transit list." ::= { atmTraceRecordEntry 5 } atmTraceRecordTraceSourceDlci OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The DLCI used on the trace source interface. The distinguished value zero indicates that no DLCI was included in the Trace transit list for the trace source interface." ::= { atmTraceRecordEntry 6 } atmTraceRecordTraceDestVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The VPI used on the preceding side of the trace destination interface. The value zero is returned if no VPI was included in the Trace transit list for the trace destination interface." ::= { atmTraceRecordEntry 7 } atmTraceRecordTraceDestVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The VCI used on the trace destination interface. The distinguished value zero indicates that no VCI was included in the Trace transit list for the trace destination interface." ::= { atmTraceRecordEntry 8 } atmTraceRecordTraceDestCallRef OBJECT-TYPE SYNTAX CallReference MAX-ACCESS read-only STATUS current DESCRIPTION "The call reference used on the trace destination interface." ::= { atmTraceRecordEntry 9 } atmTraceRecordTraceDestEndPtRef OBJECT-TYPE SYNTAX AtmEndPointReference MAX-ACCESS read-only STATUS current DESCRIPTION "The endpoint reference used on the trace destination interface." ::= { atmTraceRecordEntry 10 } atmTraceRecordTraceDestDlci OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The DLCI used on the trace destination interface. The distinguished value zero indicates that no DLCI was included in the Trace transit list for the trace destination interface." ::= { atmTraceRecordEntry 11 } atmTraceRecordTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The time at which this record entry was created." ::= { atmTraceRecordEntry 12 } atmTraceRecordTraceDestReceiveLabel OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-only STATUS current DESCRIPTION "The label for the interworking LSP used for packets transmitted in the direction of the tracing message (either SETUP, ADD PARTY, or TRACE CONNECTION) on the trace destination interface. The value zero is returned if no labels were included in the Trace transit list for the trace destination interface." ::= { atmTraceRecordEntry 13 } atmTraceRecordTraceDestTransmitLabel OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-only STATUS current DESCRIPTION "The label for the interworking LSP used for packets transmitted in the opposite direction to that of the tracing message (either SETUP, ADD PARTY, or TRACE CONNECTION) on the trace destination interface. The value zero is returned if no labels were included in the Trace transit list for the trace destination interface." ::= { atmTraceRecordEntry 14 } atmTraceInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTraceInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table in which the detailed trace information (i.e., logical nodes, logical ports, VPI/VCIs, and Call/Endpoint References) of traced connections or parties are recorded." ::= { atmTraceRecordGroup 2} atmTraceInfoEntry OBJECT-TYPE SYNTAX AtmTraceInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Trace information for one hop of an existing or new connection or party. This lists the nodes and ports traversed by the connection or party. VPI/VCIs and Call/Endpoint References may also be included in this entry. Each entry contains trace information added by one node. If there are gaps in the Trace transit list due to the use of the Pass along request flag and the presence of nodes that do not support trace, the gaps will be between successive entries in this table. Since the entries in this table are linked to the entries of the atmTraceRecordTable, the entries are added and removed from the table as and when the corresponding entries in the atmTraceRecordTable are added and removed." INDEX { atmTraceRecordIndex, atmTraceInfoSequenceIndex } ::= { atmTraceInfoTable 1 } AtmTraceInfoEntry ::= SEQUENCE { atmTraceInfoSequenceIndex Integer32, atmTraceInfoNodeId PnniNodeId, atmTraceInfoOutgoingPortId PnniPortId, atmTraceInfoIncomingVpi AtmVpIdentifier, atmTraceInfoIncomingVci AtmVcIdentifier, atmTraceInfoIncomingCallRef CallReference, atmTraceInfoIncomingEndPtRef AtmEndPointReference, atmTraceInfoRefusalIndicator TruthValue, atmTraceInfoCrankBackRcvdAtDest TruthValue, atmTraceInfoCrankBackGap TruthValue, atmTraceInfoCrankBackIndicator TruthValue, atmTraceInfoCrankBackBlockedTransitType INTEGER, atmTraceInfoCrankBackBlockedTransitInfo OCTET STRING, atmTraceInfoCrankBackCause Integer32, atmTraceInfoReceiveLabel MplsLabel, atmTraceInfoTransmitLabel MplsLabel } atmTraceInfoSequenceIndex OBJECT-TYPE SYNTAX Integer32 (1..200) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the list of logical nodes / logical ports traversed by the connection or party. The logical nodes and logical ports are given in order, as specified by this index." ::= { atmTraceInfoEntry 1 } atmTraceInfoNodeId OBJECT-TYPE SYNTAX PnniNodeId MAX-ACCESS read-only STATUS current DESCRIPTION "The node ID of a logical node traversed by the connection or party." ::= { atmTraceInfoEntry 2 } atmTraceInfoOutgoingPortId OBJECT-TYPE SYNTAX PnniPortId MAX-ACCESS read-only STATUS current DESCRIPTION "The port ID of the logical node identified in atmTraceInfoNodeId that identifies the logical port used to progress this connection or party towards the called party." ::= { atmTraceInfoEntry 3 } atmTraceInfoIncomingVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The VPI used on the succeeding side of the incoming interface of the node identified by atmTraceInfoNodeId. The value zero is returned if no VPI was included in the Trace transit list. If there are no gaps in the Trace transit list, this is the VPI used on the other side of the interface identified by the atmTraceInfoNodeId and atmTraceInfoPortId under the previous atmTraceInfoSequenceIndex." ::= { atmTraceInfoEntry 4 } atmTraceInfoIncomingVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The VCI used on the incoming interface of the node identified by atmTraceInfoNodeId. The distinguished value zero indicates that no VCI was included in the Trace transit list. If there are no gaps in the Trace transit list, this is the VCI used on the interface identified by the atmTraceInfoNodeId and atmTraceInfoPortId under the previous atmTraceInfoSequenceIndex." ::= { atmTraceInfoEntry 5 } atmTraceInfoIncomingCallRef OBJECT-TYPE SYNTAX CallReference MAX-ACCESS read-only STATUS current DESCRIPTION "The Call Reference used on the incoming interface of the node identified by atmTraceInfoNodeId. If there are no gaps in the Trace transit list, this is the call reference used on the interface identified by the atmTraceInfoNodeId and atmTraceInfoPortId under the previous atmTraceInfoSequenceIndex." ::= { atmTraceInfoEntry 6 } atmTraceInfoIncomingEndPtRef OBJECT-TYPE SYNTAX AtmEndPointReference MAX-ACCESS read-only STATUS current DESCRIPTION "The Endpoint Reference used on the incoming interface of the node identified by atmTraceInfoNodeId. If there are no gaps in the Trace transit list, this is the endpoint reference used on the interface identified by the atmTraceInfoNodeId and atmTraceInfoPortId under the previous atmTraceInfoSequenceIndex." ::= { atmTraceInfoEntry 7 } atmTraceInfoRefusalIndicator OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node identified by the atmTraceInfoNodeId refused to participate in this trace." ::= { atmTraceInfoEntry 8 } atmTraceInfoCrankBackRcvdAtDest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether a crankback was received at the node identified by the atmTraceInfoNodeId, when that node is the trace destination node and the trace destination interface is not a PNNI interface." ::= { atmTraceInfoEntry 9 } atmTraceInfoCrankBackGap OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates that the trace was propagated beyond the node identified by the atmTraceInfoNodeId, but was cranked back, and no trace information was returned by the node initiating crankback." ::= { atmTraceInfoEntry 10 } atmTraceInfoCrankBackIndicator OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether crankback information (octet group 16 of the Trace transit list information element) is present after the node identified by the atmTraceInfoNodeId, but before the next node identified in the Trace transit list information element." ::= { atmTraceInfoEntry 11 } atmTraceInfoCrankBackBlockedTransitType OBJECT-TYPE SYNTAX INTEGER { blockedIncomingLink(1), blockedNode(2), blockedOutgoingLink(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the type of blockage in case of a blocked call at the node identified by the atmTraceInfoNodeId. This object does not apply if the value of atmTraceInfoCrankBackIndicator is 'false'." ::= { atmTraceInfoEntry 12 } atmTraceInfoCrankBackBlockedTransitInfo OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This object does not apply if the value of atmTraceInfoCrankBackIndicator is 'false'. When the value of atmTraceInfoCrankBackIndicator is 'true', this object includes the contents of the Blocked Transit Trace Information field from the Trace transit list Information element." REFERENCE "PNNI Addendum for Path and Connection Trace Version 1.0, Section 3.1" ::= { atmTraceInfoEntry 13 } atmTraceInfoCrankBackCause OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the PNNI crankback cause. This object does not apply if atmTraceInfoCrankBackIndicator is set to 'false'." ::= { atmTraceInfoEntry 14 } atmTraceInfoReceiveLabel OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-only STATUS current DESCRIPTION "The label for the interworking LSP used for packets transmitted in the direction of the tracing message (either SETUP, ADD PARTY, or TRACE CONNECTION). If there are no gaps in the Trace transit list, this is from the atmTraceInfoNodeId under the previous atmTraceInfoSequenceIndex towards the atmTraceInfoNodeId under the current atmTraceInfoSequenceIndex." ::= { atmTraceInfoEntry 15 } atmTraceInfoTransmitLabel OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-only STATUS current DESCRIPTION "The label for the interworking LSP used for packets transmitted in the opposite direction to that of the the tracing message (either SETUP, ADD PARTY, or TRACE CONNECTION). If there are no gaps in the Trace transit list, this is from the atmTraceInfoNodeId under the current atmTraceInfoSequenceIndex towards the atmTraceInfoNodeId under the previous atmTraceInfoSequenceIndex." ::= { atmTraceInfoEntry 16 } atmTraceInfoNeNscTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTraceInfoNeNscEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table in which records the Ne-NSCs which tag the network entity over which the connection was established on the interfaces of the node." ::= { atmTraceRecordGroup 3} atmTraceInfoNeNscEntry OBJECT-TYPE SYNTAX AtmTraceInfoNeNscEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "One of the Ne-NSCs which tag the network entity over which the connection was established on the interface of the node." INDEX { atmTraceRecordIndex, atmTraceInfoSequenceIndex, atmTraceInfoNeNscInterface, atmTraceInfoNeNscIndex } ::= { atmTraceInfoNeNscTable 1 } AtmTraceInfoNeNscEntry ::= SEQUENCE { atmTraceInfoNeNscInterface INTEGER, atmTraceInfoNeNscIndex Integer32, atmTraceInfoNeNsc NetworkEntityNetworkServiceCategory } atmTraceInfoNeNscInterface OBJECT-TYPE SYNTAX INTEGER { incoming(1), outgoing(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the list of NSCs, used to identify the NSCs tagging resources on the incoming or outgoing interface" ::= { atmTraceInfoNeNscEntry 1 } atmTraceInfoNeNscIndex OBJECT-TYPE SYNTAX Integer32 (1..40) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the list of Ne-NSCs which tag the network entity over which the connection was established on the interface of the node. The order of the Ne-NSCs is not important" ::= { atmTraceInfoNeNscEntry 2 } atmTraceInfoNeNsc OBJECT-TYPE SYNTAX NetworkEntityNetworkServiceCategory MAX-ACCESS read-only STATUS current DESCRIPTION "One of the Ne-NSCs which tag the network entity over which the connection was established on the incoming interface of the node. " ::= { atmTraceInfoNeNscEntry 3 } atmTraceInfoRpNscTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTraceInfoRpNscEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table in which records the Rp-NSCs which tag the resource in which the connection was established on the interfaces of the node." ::= { atmTraceRecordGroup 4} atmTraceInfoRpNscEntry OBJECT-TYPE SYNTAX AtmTraceInfoRpNscEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "One of the Rp-NSCs which tag the resource in which the connection was established on the interfaces of the node." INDEX { atmTraceRecordIndex, atmTraceInfoSequenceIndex, atmTraceInfoRpNscInterface, atmTraceInfoRpNscSequenceIndex } ::= { atmTraceInfoRpNscTable 1 } AtmTraceInfoRpNscEntry ::= SEQUENCE { atmTraceInfoRpNscInterface INTEGER, atmTraceInfoRpNscSequenceIndex Integer32, atmTraceInfoRpNsc ResourcePartitionNetworkServiceCategory } atmTraceInfoRpNscInterface OBJECT-TYPE SYNTAX INTEGER { incoming(1), outgoing(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the list of NSCs, used to identify the NSCs tagging resources on the incoming or outgoing interface" ::= { atmTraceInfoRpNscEntry 1 } atmTraceInfoRpNscSequenceIndex OBJECT-TYPE SYNTAX Integer32 (1..40) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index into the list of Rp-NSCs which tag the resource in which the connection was established on the interface of the node. The order of the Rp-NSCs is not important" ::= { atmTraceInfoRpNscEntry 2 } atmTraceInfoRpNsc OBJECT-TYPE SYNTAX ResourcePartitionNetworkServiceCategory MAX-ACCESS read-only STATUS current DESCRIPTION "One of the Rp-NSCs which tag the resource in which the connection was established on the interface of the node. " ::= { atmTraceInfoRpNscEntry 3 } atmTraceIfGroup OBJECT IDENTIFIER ::= { atmTraceMIBObjects 6 } atmTraceIfTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmTraceIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to specify trace-related properties of a PNNI interface (e.g. whether a PNNI interface allows tracing over that interface)." ::= { atmTraceIfGroup 1 } atmTraceIfEntry OBJECT-TYPE SYNTAX AtmTraceIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing the trace-related properties of a PNNI interface." AUGMENTS { pnniIfEntry } ::= { atmTraceIfTable 1 } AtmTraceIfEntry ::= SEQUENCE { atmTraceIfTraceBoundary TruthValue } atmTraceIfTraceBoundary OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When this is a PNNI interface, indicates whether path and connection trace will be terminated or refused for outgoing or incoming, respectively, connections or parties on this interface. This object has no effect when this is not a PNNI interface." DEFVAL { false } ::= { atmTraceIfEntry 1 } -- Path and Connection Trace Traps atmTraceMIBTrapsPrefix OBJECT IDENTIFIER ::= { atmTraceMIB 2 } atmTraceMIBTraps OBJECT IDENTIFIER ::= { atmTraceMIBTrapsPrefix 0 } atmTraceConnCompletion NOTIFICATION-TYPE OBJECTS { atmTraceConnRecordIndex } STATUS current DESCRIPTION "An atmTraceConnCompletion trap is sent when enabled and either a TRACE CONNECTION ACKNOWLEDGE message is received at the trace source node, or after atmTraceConnFailTimeout has passed without any response (i.e., the connection trace fails)." ::= { atmTraceMIBTraps 1 } atmTracePathTestCompletion NOTIFICATION-TYPE OBJECTS { atmTracePathTestRecordIndex } STATUS current DESCRIPTION "An atmTracePathTestCompletion trap is sent when enabled and the test connection or test party becomes active on the trace source interface, or is cleared across the trace source interface." ::= { atmTraceMIBTraps 2 } atmTracePathFilterTrap NOTIFICATION-TYPE OBJECTS { atmTraceFilterRecordConnKind } STATUS current DESCRIPTION "An atmTracePathFilter trap is sent when the trap is enabled and a record is added to the atmTraceRecordTable and the atmTraceFilterRecordTable corresponding to this filter. The atmTraceFilterTrapEnable object must be reset to 'true' before another atmTracePathFilter trap can be generated by the agent for this filter entry." ::= { atmTraceMIBTraps 3 } -- conformance information atmTraceMIBConformance OBJECT IDENTIFIER ::= { atmTraceMIB 3 } atmTraceMIBCompliances OBJECT IDENTIFIER ::= { atmTraceMIBConformance 1 } atmTraceMIBGroups OBJECT IDENTIFIER ::= { atmTraceMIBConformance 2 } -- compliance statements atmTraceMIBCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the PNNI Addendum for Path and Connection Trace Version 1.1. Groups of objects required to support certain functionality are identified by the suffix MandatoryGroup. Groups of optional objects are identified by the suffix OptionalGroup." MODULE -- this module MANDATORY-GROUPS { atmTraceMIBMandatoryGroup } GROUP atmTraceConnAndPathFilterMandatoryGroup DESCRIPTION "Required if connection trace or path trace using filtering of new connection and party establishment messages is supported." GROUP atmTracePathMandatoryGroup DESCRIPTION "Required if path trace is supported." GROUP atmTraceConnMandatoryGroup DESCRIPTION "Required if connection trace is supported." GROUP atmTracePathTestMandatoryGroup DESCRIPTION "Required if path trace using test connections and parties is supported." GROUP atmTracePathFilterMandatoryGroup DESCRIPTION "Required if path trace is supported using filtering of new connection and party establishment messages." GROUP atmTraceConnAndPathFilterPolicyMandatoryGroup DESCRIPTION "Required if connection trace or path trace using filtering of new connection and party establishment messages and policy tracing is supported." GROUP atmTraceConnPolicyMandatoryGroup DESCRIPTION "Required if connection trace and policy tracing is supported." GROUP atmTracePathTestPolicyMandatoryGroup DESCRIPTION "Required if path trace using test connections and parties and policy tracing is supported." GROUP atmTracePathFilterPolicyMandatoryGroup DESCRIPTION "Required if path trace using filtering of new connection and party establishment messages and policy tracing is supported." GROUP atmTraceConnAndPathFilterMplsMandatoryGroup DESCRIPTION "Required if connection trace or path trace using filtering of new connection and party establishment messages and interworking LSP label tracing is supported." GROUP atmTraceConnMplsMandatoryGroup DESCRIPTION "Required if connection trace and interworking LSP label tracing is supported." GROUP atmTracePathTestMplsMandatoryGroup DESCRIPTION "Required if path trace using test connections and parties and interworking LSP label tracing is supported." GROUP atmTracePathFilterMplsMandatoryGroup DESCRIPTION "Required if path trace using filtering of new connection and party establishment messages and interworking LSP label tracing is supported." OBJECT atmTraceTransitListMaximumSize MIN-ACCESS read-only DESCRIPTION "Maximum size of the Trace transit list information element larger than 1466 octets is optional." OBJECT atmTraceConnOrigConnType SYNTAX INTEGER { atmVcc(2) } MIN-ACCESS read-only DESCRIPTION "The ability to trace connections other than ATM VCCs (e.g. ATM VPCs, bearer-independent ATM connections, frame relay connections) is optional." OBJECT atmTraceConnOrigDirection SYNTAX INTEGER { incoming(1) } MIN-ACCESS read-only DESCRIPTION "The ability to trace connections and parties starting from the outgoing interface of a device is optional." OBJECT atmTracePathTestConnType SYNTAX INTEGER { atmVcc(2) } MIN-ACCESS read-only DESCRIPTION "The ability to generate test connections for path trace other than ATM VCCs (e.g. ATM VPCs, bearer-independent ATM connections) is optional." OBJECT atmTracePathTestClearCallAtTDest MIN-ACCESS read-only DESCRIPTION "The ability to generate test connections and parties that remain active after the path trace is completed is optional." OBJECT atmTraceFilterClearCallAtTDest MIN-ACCESS read-only DESCRIPTION "The ability to indicate call clearing at the trace destination node for calls that match a certain filter at the trace source node is optional." ::= { atmTraceMIBCompliances 2 } -- units of conformance atmTraceMIBMandatoryGroup OBJECT-GROUP OBJECTS { atmTraceMaxConcurrentRequests, atmTraceAvailableRequests, atmTraceTransitListMaximumSize, atmTraceRecordStatus, atmTraceRecordTraceSourcePortId, atmTraceRecordTimeStamp, atmTraceInfoNodeId, atmTraceInfoOutgoingPortId, atmTraceInfoRefusalIndicator } STATUS current DESCRIPTION "A collection of objects required when path or connection trace is supported." ::= { atmTraceMIBGroups 1 } atmTraceMIBOptionalGroup OBJECT-GROUP OBJECTS { atmTraceRecordTraceSourceDlci } STATUS current DESCRIPTION "A collection of optional objects used for path and connection trace." ::= { atmTraceMIBGroups 2 } atmTraceConnAndPathFilterMandatoryGroup OBJECT-GROUP OBJECTS { atmTraceRecordTraceDestVpi, atmTraceRecordTraceDestVci, atmTraceRecordTraceDestCallRef, atmTraceRecordTraceDestEndPtRef, atmTraceRecordTraceDestDlci, atmTraceInfoIncomingVpi, atmTraceInfoIncomingVci, atmTraceInfoIncomingCallRef, atmTraceInfoIncomingEndPtRef } STATUS current DESCRIPTION "A collection of objects required when supporting connection trace or path trace using filtering of new connection and party establishment messages." ::= { atmTraceMIBGroups 3 } atmTracePathMandatoryGroup OBJECT-GROUP OBJECTS { atmTraceRecordCause, atmTraceRecordDiags, atmTraceInfoCrankBackRcvdAtDest, atmTraceInfoCrankBackGap, atmTraceInfoCrankBackIndicator, atmTraceInfoCrankBackBlockedTransitType, atmTraceInfoCrankBackBlockedTransitInfo, atmTraceInfoCrankBackCause } STATUS current DESCRIPTION "A collection of objects required when supporting path trace." ::= { atmTraceMIBGroups 4 } atmTraceConnMandatoryGroup OBJECT-GROUP OBJECTS { atmTraceConnOwner, atmTraceConnTraceSourceIf, atmTraceConnOrigConnType, atmTraceConnOrigVpi, atmTraceConnOrigVci, atmTraceConnEndPtRef, atmTraceConnOrigDirection, atmTraceConnTraceConnId, atmTraceConnTraceCallRef, atmTraceConnPassAlongRequest, atmTraceConnFailTimeout, atmTraceConnAgeTimeout, atmTraceConnRestart, atmTraceConnRecordIndex, atmTraceConnRowStatus } STATUS current DESCRIPTION "A collection of objects required when connection trace is supported." ::= { atmTraceMIBGroups 5 } atmTraceConnOptionalGroup OBJECT-GROUP OBJECTS { atmTraceConnCallRef, atmTraceConnOrigDlci, atmTraceConnTrapOnCompletion } STATUS current DESCRIPTION "A collection of optional objects used for connection trace." ::= { atmTraceMIBGroups 6 } atmTracePathTestMandatoryGroup OBJECT-GROUP OBJECTS { atmTracePathTestOwner, atmTracePathTestConnType, atmTracePathTestConnCastType, atmTracePathTestTraceSourceIf, atmTracePathTestP2MpNewConn, atmTracePathTestOrigVpi, atmTracePathTestOrigVci, atmTracePathTestCalledParty, atmTracePathTestTxTrafDescrIndex, atmTracePathTestRxTrafDescrIndex, atmTracePathTestClearCallAtTDest, atmTracePathTestTraceCrankback, atmTracePathTestPassAlongRequest, atmTracePathTestAgeTimeout, atmTracePathTestRestart, atmTracePathTestRecordIndex, atmTracePathTestRowStatus } STATUS current DESCRIPTION "A collection of objects required when path trace using test connections and test parties is supported." ::= { atmTraceMIBGroups 7 } atmTracePathTestOptionalGroup OBJECT-GROUP OBJECTS { atmTracePathTestCallingParty, atmTracePathTestTraceConnId, atmTracePathTestTraceCallRef, atmTracePathTestTrapOnCompletion } STATUS current DESCRIPTION "A collection of optional objects used for path trace using test connections and test parties." ::= { atmTraceMIBGroups 8 } atmTracePathFilterMandatoryGroup OBJECT-GROUP OBJECTS { atmTraceFilterControl, atmTraceFilterOwner, atmTraceFilterConnKind, atmTraceFilterInIf, atmTraceFilterCalledPartyPrefix, atmTraceFilterCalledPartyLength, atmTraceFilterClearCallAtTDest, atmTraceFilterTraceCrankback, atmTraceFilterTraceConnId, atmTraceFilterTraceCallRef, atmTraceFilterPassAlongRequest, atmTraceFilterMaxRecords, atmTraceFilterStopTimeout, atmTraceFilterAgeTimeout, atmTraceFilterPurge, atmTraceFilterNumMatches, atmTraceFilterRowStatus, atmTraceFilterRecordConnKind, atmTraceFilterRecordConnCastType, atmTraceFilterRecordServiceCategory, atmTraceFilterRecordInIf, atmTraceFilterRecordOutIf, atmTraceFilterRecordCallingParty, atmTraceFilterRecordCalledParty } STATUS current DESCRIPTION "A collection of objects required when path trace is supported using filtering of new connection and party establishment messages." ::= { atmTraceMIBGroups 9 } atmTracePathFilterOptionalGroup OBJECT-GROUP OBJECTS { atmTraceFilterConnCastType, atmTraceFilterServiceCategory, atmTraceFilterOutIf, atmTraceFilterCallingPartyPrefix, atmTraceFilterCallingPartyLength, atmTraceFilterRecordCountDown, atmTraceFilterTrapEnable } STATUS current DESCRIPTION "A collection of optional objects used for path trace using filtering of new connection and party establishment messages." ::= { atmTraceMIBGroups 10 } atmTraceIfOptionalGroup OBJECT-GROUP OBJECTS { atmTraceIfTraceBoundary } STATUS current DESCRIPTION "A collection of optional objects used to configure PNNI interfaces to refuse incoming and terminate outgoing path and connection traces." ::= { atmTraceMIBGroups 11 } atmTraceNotificationOptionalGroup NOTIFICATION-GROUP NOTIFICATIONS { atmTraceConnCompletion, atmTracePathTestCompletion, atmTracePathFilterTrap } STATUS current DESCRIPTION "A collection of optional notifications used for path and connection trace." ::= { atmTraceMIBGroups 12 } atmTraceConnAndPathFilterPolicyMandatoryGroup OBJECT-GROUP OBJECTS { atmTraceInfoNeNsc, atmTraceInfoRpNsc } STATUS current DESCRIPTION "A collection of objects required when supporting connection trace or path trace using filtering of new connection and party establishment messages and policy tracing." ::= { atmTraceMIBGroups 13 } atmTraceConnPolicyMandatoryGroup OBJECT-GROUP OBJECTS { atmTraceConnTraceNeNsc, atmTraceConnTraceRpNsc, atmTraceConnTraceIncoming } STATUS current DESCRIPTION "A collection of objects required when connection trace and policy tracing is supported." ::= { atmTraceMIBGroups 14 } atmTracePathTestPolicyMandatoryGroup OBJECT-GROUP OBJECTS { atmTracePathTestTraceNeNsc, atmTracePathTestTraceRpNsc, atmTracePathTestTraceIncoming } STATUS current DESCRIPTION "A collection of objects required when path trace using test connections and test parties and policy tracing are supported." ::= { atmTraceMIBGroups 15 } atmTracePathFilterPolicyMandatoryGroup2 OBJECT-GROUP OBJECTS { atmTraceFilterPolicy, atmTraceFilterTraceNeNsc, atmTraceFilterTraceRpNsc, atmTraceFilterTraceIncoming } STATUS current DESCRIPTION "A collection of objects required when path trace using filtering of new connection and party establishment messages and policy tracing is supported." ::= { atmTraceMIBGroups 16 } atmTraceConnAndPathFilterMplsMandatoryGroup OBJECT-GROUP OBJECTS { atmTraceRecordTraceDestReceiveLabel, atmTraceRecordTraceDestTransmitLabel, atmTraceInfoReceiveLabel, atmTraceInfoTransmitLabel } STATUS current DESCRIPTION "A collection of objects required when supporting connection trace or path trace using filtering of new connection and party establishment messages and interworking LSP label tracing." ::= { atmTraceMIBGroups 17 } atmTraceConnMplsMandatoryGroup OBJECT-GROUP OBJECTS { atmTraceConnTraceLabels } STATUS current DESCRIPTION "A collection of objects required when connection trace and interworking LSP label tracing is supported." ::= { atmTraceMIBGroups 18 } atmTracePathTestMplsMandatoryGroup2 OBJECT-GROUP OBJECTS { atmTracePathTestTraceLabels } STATUS current DESCRIPTION "A collection of objects required when path trace using test connections and test parties and interworking LSP label tracing are supported." ::= { atmTraceMIBGroups 19 } atmTracePathFilterMplsMandatoryGroup2 OBJECT-GROUP OBJECTS { atmTraceFilterTraceLabels } STATUS current DESCRIPTION "A collection of objects required when path trace using filtering of new connection and party establishment messages and interworking LSP label tracing is supported." ::= { atmTraceMIBGroups 20 } -- deprecated definitions - compliance statements atmTraceMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities which implement the PNNI Addendum for Path and Connection Trace Version 1.0. Groups of objects required to support certain functionality are identified by the suffix MandatoryGroup. Groups of optional objects are identified by the suffix OptionalGroup." MODULE -- this module MANDATORY-GROUPS { atmTraceMIBMandatoryGroup } GROUP atmTraceConnAndPathFilterMandatoryGroup DESCRIPTION "Required if connection trace or path trace using filtering of new connection and party establishment messages is supported." GROUP atmTracePathMandatoryGroup DESCRIPTION "Required if path trace is supported." GROUP atmTraceConnMandatoryGroup DESCRIPTION "Required if connection trace is supported." GROUP atmTracePathTestMandatoryGroup DESCRIPTION "Required if path trace using test connections and parties is supported." GROUP atmTracePathFilterMandatoryGroup DESCRIPTION "Required if path trace is supported using filtering of new connection and party establishment messages." OBJECT atmTraceTransitListMaximumSize MIN-ACCESS read-only DESCRIPTION "Maximum size of the Trace transit list information element larger than 1466 octets is optional." OBJECT atmTraceConnOrigConnType SYNTAX INTEGER { atmVcc(2) } MIN-ACCESS read-only DESCRIPTION "The ability to trace connections other than ATM VCCs (e.g. ATM VPCs, bearer-independent ATM connections, frame relay connections) is optional." OBJECT atmTraceConnOrigDirection SYNTAX INTEGER { incoming(1) } MIN-ACCESS read-only DESCRIPTION "The ability to trace connections and parties starting from the outgoing interface of a device is optional." OBJECT atmTracePathTestConnType SYNTAX INTEGER { atmVcc(2) } MIN-ACCESS read-only DESCRIPTION "The ability to generate test connections for path trace other than ATM VCCs (e.g. ATM VPCs, bearer-independent ATM connections) is optional." OBJECT atmTracePathTestClearCallAtTDest MIN-ACCESS read-only DESCRIPTION "The ability to generate test connections and parties that remain active after the path trace is completed is optional." OBJECT atmTraceFilterClearCallAtTDest MIN-ACCESS read-only DESCRIPTION "The ability to indicate call clearing at the trace destination node for calls that match a certain filter at the trace source node is optional." ::= { atmTraceMIBCompliances 1 } END